Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Why does it die when I apply brakes?
User Name
Password
lost password?   |   register now

Thread: Why does it die when I apply brakes? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-20-2012 01:42 PM
jjj I am certain that the condition exists even when the brake booster is taken off-line. I will search under the dash to have a look at the brake pedal switch. I am not certain that the switch could be the cause of the problem- not sure where or how the switch could cause a ground strong enough to kill the engine... any other ideas are welcomed.

Thanks in advance.
10-19-2012 12:41 PM
alittle1 Got cruise on it?

When you touch the brake, cruise will come off normally. If switch is screwed, it could kill the engine by backfeeding to ground.

Also, check the electric solenoid that sets up the carb idle, when ignition is turned on the solenoid will pull the linkage and add a couple hundred rpms to start engine and when turning the engine off, it will disengage solenoid and linkage to avoid run-on of engine. Engaging A/C also adds rpm.
10-19-2012 10:05 AM
hcompton Does it sputter some times or go off like a switch. Could be low fuel level in the float bowls. was a common issue back in the day. You would slam on the breaks or break for a few seconds and the motor would sputter right out. Could aslo be same problem in reverse with too much fuel.

Hope this helps.
10-19-2012 06:05 AM
E.Furgal look for a pinched wire under dash thats getting pinched when your on the brake..

or a loose ign switch on the column at the base..
10-19-2012 03:51 AM
75gmck25 Your first troubleshooting sounds reasonable, so I'm surprised you did not find a bad brake booster that was screwing up the vacuum.

However, if its not vacuum, then maybe its electrical. Something may be grounding out when you press the pedal, or a sudden electrical load may be causing such a draw on the alternator that it pulls the idle down very quickly and it dies.

- Hold the brake pedal down and start the car. Try this in several positions of the pedal travel. What you are looking for is a point where something grounds out and causes an electrical problem. If you have an aftermarket tach, take a close look at the wiring to the HEI to make sure you don't have a wire running next to the brake pedal arm that is grounding out the ignition.

- Try pulling the fuse for the brake lights to see if it resolves the problem. I don't think the lights could put enough load on the alternator to pull the idle down significantly, but maybe something else (add-on 3rd brake light?) is drawing excessive power. Check for any relays that might be connected to the brake light circuit. If someone has added any aftermarket security devices, that would also be a good place to start.

Bruce
10-19-2012 03:03 AM
jjj
Why does it die when I apply brakes?

my 74 El Camino- stock 350/TH350 (not TH350C) has been running tip top. All of a sudden it dies when I apply the brake during idle- like at a stoplight.

I thought vacuum leak: Disconnected the brake booster hose at the intake and plugged the intake there... same deal!?

Anything else I can look at?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:41 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.