Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> carb spacer
User Name
Password
lost password?   |   register now

Thread: carb spacer Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-29-2013 07:45 PM
kc8oye edit: looking at the pics.. it was the float height adjusters the air cleaner wouldn't clear by itself. and the plastic spacers were cheaper than a new base
12-29-2013 07:43 PM
kc8oye I learned it quite accidently. I had a drop base air cleaner and the air cleaner base wouldn't clear the vac. secondary pod i think it was. so I added a plastic spacer between the carb and air cleaner...

i had to modify it slightly to clear the choke linkages..
http://home.comcast.net/~kc8oye/Engine/DSC03089.JPG

My dad was a GM Powertrain engineer.. and oddly enough, I remember him telling me one day, how important air flow through the air cleaner and into the carb was.. (I think was askign about that that little deflector plate at the base of the factory snorkel air cleaner)

so I decided to take it to the extreme. i put all the spacers I could fit with the piece of threaded rod I had available.. this is what I wound up with.

http://home.comcast.net/~kc8oye/body/hood_clearance.jpg

that's looking across the surface of the hood ~

add to that, a correctly positioned cowl induction scoop... and it made a *HUGE* difference in how it ran.. I wish I had thought to make some 'before' passes at the track to get some quantifiable numbers tho

this was a trial-fitting pic.. that's why it's such a mess lol.
http://home.comcast.net/~kc8oye/body/hood_side.jpg


here's one last pic that shows just how high up my air cleaner stands from the carb..
http://home.comcast.net/~kc8oye/Engine/DSCN0764.JPG
12-29-2013 07:23 PM
techinspector1
Quote:
Originally Posted by kc8oye View Post
You would be surprised what a difference a spacer between the carb and air cleaner can make too!
I agree, that's the problem with a drop-base air cleaner base.....it chokes off the flow of air to the motor. I like to use a 14" x 3" or 14" x 4" filter element and get it up off the manifold.
12-29-2013 07:12 PM
kc8oye You would be surprised what a difference a spacer between the carb and air cleaner can make too!
12-17-2013 04:22 PM
techinspector1 Spacers are an unknown quantity. You never know how the motor will like them until you get some drag strip time slips using no spacer, then a short spacer, then a tall spacer. Back to back drag strip passes are the only scientific way to assess a speed part, other than a dyno.
10-24-2012 08:56 AM
my87Z Personally I would run the 1" spacer, you already picked the smaller runner Performer intake instead of the performer rpm intake (I would have gone with the rpm), but it wont make that much of difference. Like someone mentioned before it will act as if you had slightly larger runners, you still have the divider plenum so the their wont be any swirling and and turbulance will still be fine.


I actually ran a 383, ment for strip/strip with a performer rpm with a 1" spacer, I had the plenum divider milled down 1/2" (got the idea from a dyno show). I had that 383 dyno'd with both a victor jr and this modified rpm intake, the vic jr made alittle more high end hp but the modified rpm made considerably more tq.
10-24-2012 07:36 AM
poncho62 Cant you just grind off the linkage or EGR a bit where it is hitting?
10-24-2012 07:19 AM
JasonL
4 hole

Guess i will get a 4 hole one. I am looking to keep as much low end as possible. i would run no spacer if the carb linkage did not hit the egr part of the intake. I am thinking of just getting a 1/2" one. It will give me plenty of room and hopefully not kill the low end.
10-24-2012 05:18 AM
hcompton The open spacer will effect the intakes dual plane design. But it may effect for the better depending on the setup. I would give the open 1" spacer a try and if that does not provide good low end power move to a four hole spacer for added punch down low.

It wont hurt anything and you can use the same type so you dont have to change the linkage if you want to swap the spacer. For the four hole type later on. A lot of people run open spacers on dual plane intakes as it will amke you intake seem bigger to the engine than it is.

hope this helps.
10-24-2012 05:02 AM
JasonL
carb spacer

hello all, finally got my motor together and need to use a carb spacer. I have a 355, 9:1cr, 268HE cam, 492 heads, performer intake. Holley 670 vac sec carb. I need a spacer and I have a open one (1"). Is this ok, or should i get a 4 hole one. I can go to a 1/2" also, just need to clear the linkage.

Motor

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:32 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.