|12-23-2012 11:42 AM|
I bought my Monza in 2008 & have thousands of passes on it. A cheap and fast upgrade DIY is front spindles, brakes & rear end from S10 , Weld in a cage kit from Jegs. Buy a v8 monza pan or milodon & moroso make H body specifics. Hooker or hedman hedders Trans dap still makes an engine swap kit so you can use big headers.
V8monza.com & H body.org is a good start. The 96 inch wheelbase makes you have to drive it & its a blast. Cheap fun and the fans luv it.
|12-22-2012 08:41 AM|
|swvalcon||All depends on what hp you plan to put to it. 450 up I would build a tube frame for it. Check out my project journal.|
|12-18-2012 08:29 PM|
Whatever you start with, inspect the car for rust with an ice pick. Here's a nice rust-free example of a wagon I came across....
1972 Chevrolet Vega | Red 1972 Chevrolet Vega Classic Car in Murphy NC | 3202785820 | Used Cars on Oodle Marketplace
|12-18-2012 08:23 PM|
|12-18-2012 07:30 PM|
|ogre||vega wagon is the way to go|
|12-18-2012 04:46 PM|
|1971BB427||With decent fab skills and the right equipment, just about any body can be made into a drag car. Needs to meet the minimum wheelbase length, but a Vega already does that. My car doesn't meet minimum wheelbase, so I'm stuck running non NHRA tracks.|
|12-18-2012 03:52 PM|
A 71 for sale:
71 Vega For Sale
Just repaint it, and change the rear-end gears.
|12-18-2012 03:45 PM|
It takes me longer than a weekend just to measure and decide what stuff I need to order!
|12-18-2012 12:42 PM|
you will need to stitch weld all the unibody seams from the firewall forward to help stiffen up things in the front. A roll cage is a plus if you plan on drag racing it more than just occasionally. You can swap in S10 front suspension/brakes and S10 rear end.
|12-05-2012 05:20 PM|
u wanta play with a mavrick
brother has one.. i think its a '74 body.. mostly alum, caged. is a race car but he needs to finish the engine/trans...
but he's think'n of selling it... $4500 bucks..
|12-05-2012 05:11 PM|
|12-05-2012 04:29 AM|
I back haft'ed a Monza Town coupe which is the same platform as a Vega.They ALL rot out in the rear wheel well where the trailing arms attach to the body.It is a weak point.Back then I used a Don Hardy kit with a 6 point roll bar.I honestly don't know if don Hardy is around anymore.I spent a ton of time rebuilding the floor boards on that car.The Don Hardy kit jets in and out of the floor boards with the raise going over the rear end being a 2 x 3 square tube and then flipping over on it's side to the 3 x 2 side all the way up to the rear of the A-Frame supports.When you buy a roll bar you get a box of tubes none cut to size and you need to tight seam fish mouth fit some of the tubes.I had the car off the ground like 4' with the rear end out and perfectly level so all the ref points where dead on.The stock rear ends are a trailing arm with a pivot arm to the rear end off the back of the tranny.I am not 100% sure,but the Monzas did come with a 305,so there might be a crossover in engine mounts there you could use.
What became a standard joke in the shop was the articles about sub and tube in a weekend.The one we did we had three months into it working on it on and off.But be advised it is a hell of alot work.Of memory serves me correctly,the curb wt of that car was somewhere in the range of 2800lbs.
When we first got the frame rails in it,you could take a hammer and hit them and they would ring like a bell.As we put in more and more of the roll bar,that got less and less until it was just a thud.It's all about how well those roll bars tie everything together.Once done,I could take a jack in the center of the car under one of the frame rails and easily lift the whole side of the car up.
My advise would be for you to buy a proven roller from racingjunk.com.One fact never changes.You can never build one for the same price as one already done and maybe done better than you could.
|12-04-2012 11:06 PM|
How about an AMC Pacer, or a Gremlin? How about a tubbed Chevette?
( I wanna see a tubbed Toyota Yaris hatchback! )
To heck with going small and light... let's do up a 1974 Cadillac Eldorado with a Gene Fulton 707 heavy street motor and a air-shifted Lenco!
|12-04-2012 08:13 PM|
It all depends on what you want to do with it.
The singular advantage of them- weight. The disadvantages are basically everything else.
One light car that is much easier to work with has been mentioned- the Pinto. I have one and parts availability is actually really good and relatively low priced, and they are also very light.
|12-04-2012 06:53 PM|
Oh, I almost forgot.... to answer your question:
The DOWNSIDE to a Chevy Vega is: you can't find them anymore!
I see some on Racingjunk.com, but they are all very far away from me.
( So if you find one.... get it. )
|This thread has more than 15 replies. Click here to review the whole thread.|