|01-21-2013 07:18 AM|
|BuzzLOL||.. Yes, the more powerful the longblock, the more restrictive the 2bbl. is going to seem to be...|
|01-18-2013 07:33 PM|
Cam Quest download
Estimated difference in HP between a 2 bbl (350 cfm) and a 600 cfm 4 bbl:
• All 2bbl peaks are: hp @ 4000 rpm/tq @ 2000 rpm regardless of cam (of these three).
• All hp peaks are at 4000 rpm, regardless of cam or 2bbl or 4bbl carb.
• With 4bbl, tq peak is 500 rpm higher w/each cam change.
12-300-4 - HIGH Energy
240H cam w/2bbl: 222 hp @ 4000 rpm/363 tq @ 2000 rpm
240H cam w/4bbl: +26 hp/+9 tq @ 2500 rpm; Avg. power +13 tq/+15 hp
12-305-2 - PURE Energy
246PE cam w/2bbl: 225 hp/356 tq
246PE cam w/4bbl:+30 hp/+14 tq @ 3000 rpm; Avg. power +13 hp/+17 tq
12-207-2 - DUAL Energy
255DEH cam w/2bbl: 231/348
255DEH cam w/4bbl:+30 hp/+21 tq @ 3500 rpm; Avg. power +8 hp/+10 tq
|01-17-2013 07:12 PM|
|cadillacdave1||A stock 2 barrel intake will not bolt up to a vortec cylinder head|
|01-17-2013 05:30 PM|
|01-11-2013 07:33 PM|
|BuzzLOL||.. Did you get any further on this?|
|12-18-2012 02:42 PM|
|Jkingof956||i just installed a muffler, i will be looking for a posi unit, and going with 700r4 fully build, another reason why so cheap build is because i already have most of the upgrades some were free and ready to install|
|12-17-2012 09:06 PM|
|12-17-2012 09:00 PM|
|12-17-2012 08:55 PM|
|12-17-2012 01:32 AM|
|BuzzLOL||.. Those cars were known for terrible 9-11 MPG and sluggish performance with dished pistons and big 76cc chamber heads... nominal 8.5:1, but actually ~7.6:1 compression ratio. I'd definitely go stock type 4-eyebrow flat top pistons or even 2-eyebrow hypereutectic flat or minidome pistons such as KBs if they fit your budget to get power up throughout the RPM range and cruising MPG up near 17-20 MPG. That cam needs at least 9.5 and preferably 10.5-11.0 compression ratio to run STRONG, which is what you must have to win your race. Power should be 350-400 HP with that cam and Vortec heads depending on other final components used. Torque peak around 4000 RPMs, HP peak around 5500-5700 RPMs, shift at 6,000+ RPMs when racing. The factory RPM range suggested for that 214/224 cam is conservatively much lower because they don't know if you're putting it into a slug stock 7.6:1 engine, which most prolly are, yielding disappointing results. Borrow some short 275-50R-15 (or shorter) drag radials for the track. A 2-bbl. carb. would run fine but start noticably falling on its face at a low 3500 RPMs. Put a properly tuned vacuum secondary 750CFM carb. on it. 600 CFM carb.s usually come default tuned for 305" and slug 350" engines. You'll prolly need the 3000 stall converter to win your race.|
|12-17-2012 12:55 AM|
good luck the mustangs almost 900 lb lighter..
my dads old olds 77 cutlass s was 4178 lb with power windows/locks tilt and buckets console..
they took alot of metal out in 78. as my SS loaded is 3416
|12-16-2012 09:46 PM|
|BigEd36||Jkingof956, with the Summit K1103 cam and Vortec heads I believe you should be in the area of your 350 HP goal. The GMPP CT 350 (350 CI 350 HP) crate circle track engine uses a stock 350 shortblock with vortec heads and the #24502476 cam (.435"/.460" lift, 212*/222* @ .050", 112* LSA). Your Summit K1103 has just slightly more lift and duration (.442"/.465", 214*/224* at .050", 112* LSA).|
|12-16-2012 07:46 PM|
|12-16-2012 03:21 PM|
You can get some good stock four intakes and carbs that will make ok power but not as good as edelbrock. But will look dead factory under the hood. Same goes for manifolds that will flow enough to make good power. Usally some port work on factory manifolds is all that is needed if the right casting a choosen. But this is kind of art with the oem parts swapper guys. I can really help with all the part numbers needed to pull it off. But the 350 hp sounds possible.
I do think having the factory under the hood will be worth every penny if you plan on selling the car. If a buyer looks under the hood and sees intake and headers they always think the worst. Unless they know the engine builder and then still its a harder sale than oem stock look. No one complains if its four barrel and not a two. But headers will drop the pirce a bit unless they are a work of art in them selves.
|12-16-2012 03:14 PM|
your best chance to beat him cheap,,,take some weight out of the car and find a very short pair of sticky tires.
The Mustang is lighter and has a very low 3.27 first gear. You might 1/4 mile him but he might 1/8 mile beat you.
|This thread has more than 15 replies. Click here to review the whole thread.|