Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 455 pistons and gaskets
User Name
Password
lost password?   |   register now

Thread: 455 pistons and gaskets Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-14-2013 08:37 AM
Mr. P-Body Still not sure what you're driving at here. The "funny car" reference?

The "recipe" you supplied for an old Pontiac is from the 1970s. Race gas and high compressin are for RACE CARS, not street cars. With that cam/head combination, the engine will make MAYBE 450 HP, be out of breath at 5,800 and in general, be a slug except in a light car with stiff gears.

Today, we take a completely different approach to building a powerful Pontiac. Porting the heads is paramount. The little intake ports are fine for a "stocker", but won't let a 455 rev.

While it may not be "necessary" to rev a Pontiac hard to make power (unlike the SBC), why not have "both"? It's nearly impossible to "tune" the low-end power "out". So, add parts to make it breath, and will make low-end power AND rev. Solid lifters also make a HUGE difference in performance. If the budget can stand it, solid rollers are "the best". Comp has some very nice "street" grinds in the XE series, just for the lower compression and higher revs.

It's not uncommon at all, to have 550-600 HP and 600 lb ft. with 93 octane, under 6,000. How about spinning it to 7.500? WOO-HOO!

Jim
01-13-2013 02:16 PM
MouseFink Cool aid quality pump gas is bad now and is getting worse so people must build their emissions engines accordingly.

Providing that you have an engine that does not have emissions restrictions, such as those without a catalytic converter you can get 12:1 static compression ratio, 9.4:1 dynamic compression ratio, and 220 lb. cranking cylinder pressure would be the limit before you must O-ring the block.

Get it with an "Old School" 1970 455 CI Pontiac, 1967 GTO/Firebird 400 heads (#670), Comp Cams 041H Ram Air IV camshaft, Borg Warner Super T10 with a 2.64 low, 3.90:1 gears, 100%, VP C12, 108 octane racing fuel at $14 per gallon and plenty of "bite" fills the bill nicely.
01-13-2013 10:53 AM
Mr. P-Body Mousefink,

Funny cars? Hydraulic cams?

It's very important to most folks today, to run well on "pump gas", 93 or lower octane. Using 108 in a street car is not practical. The Pontiac chamber is "unique", both a blessing and a curse. When octane is right, timing is right and the engine is "happy", the chamber provides good power and lower emmissions than most others of the era. That same efficiency makes them very prone to detonation when things aren't EXACTLY right (erred on the side of "danger", not "caution").

Jim
01-10-2013 03:06 PM
MouseFink 1967-1970 GTO/Firebird 400 heads
455 CI
11.8:1 static compression ratio
10.8:1 dynamic compression ratio
Melling SPC-8 Ram Air IV camshaft
Comp Cams 863 limited travel lifters
Richmond 4-speed
3.64:1 rear cogs
BF Goodrich Drag radials.
100% VP C-12 108 octane racing fuel

Run with the funny cars.
01-10-2013 02:26 PM
cobalt327
Quote:
Originally Posted by Mr. P-Body View Post
...9.5:1 (accepted limit for 93 octane and iron heads on a Pontiac)
Quote:
Originally Posted by cobalt327
The OP's 4X 455 heads w/a 0.060" cut and FT pistons and a 0.041" quench will give him right at 9.1:1; 9.5:1 is the max I, or anyone who knows what they're talking about regarding Pontiac engines w/iron heads would recommend he use, anyway.
blakethechop, you would do well to follow the recommendations shown here regarding Pontiac CR w/iron heads.
01-10-2013 09:03 AM
hcompton High compression on a poncho is not the end of the world. a lot of street cars run large cams with high compression engines. They dont knock if the DCR is correct. Factory cam on factory heads knock.
01-10-2013 07:23 AM
Mr. P-Body 455 ring pack has a 5/64" top ring, 1/16" second ring and 3/16" oil ring. Stock dimensions. The increase in stroke from 4" to 4.210" added significant wear to the second ring, so the size reduction was made before the engine went into production.

The Speed Pro L2359F is FAR superior to the KB piston. We use them (KBs) for ash trays. The Icon forgings, however, are every bit as good, if not better than the Speed Pros, and lighter, for about the same money.

In order for a "flat top" piston'd 455 to make under 9.5:1 (accepted limit for 93 octane and iron heads on a Pontiac) requires 98 CCs in the chamber/dish, not including the gasket. Purge the term "get away with" from your vocabulary. Do it right.

Also, be certain to install new FORGED connecting rods. Don't let ANYONE convince you you don't need them. The original rods are a cast steel, and were inadequate when NEW, much less 40 years later... RPM rods make a nice replacement for a reasonable price (about the same cost as new bolts and resizing the old rods).

Be sure to get Jim Hand's "How to Build Max-performance Pontiac V8s" by SA Designs. It's the most current study of the ol' Injun. There's a "rewrite" in process, but none of the original "players" were consulted. The "tractor motor" crowd has hijacked the book. It's okay. Still TONS of good info on modern builds "out there". And we HAVE learned how to build Pontiacs that rev just like any other brand... (we shifted Dirty Bird @ 9,200, a 475 CID Pontiac blown/alcohol, about 2,200 HP) But they STILL make a bunch more low-end than the "other" GM engines that are popular among the racer crowd.

FWIW

Jim
01-07-2013 11:21 PM
cobalt327 He has 4X 455 heads that he has to use, big chambers, no prob. w/too much CR. Good catch on the ring size, though. Was looking at the 428 KB's http://www.kb-silvolite.com/assets/a...ve_catalog.pdf.
01-07-2013 08:11 AM
MouseFink If you use those pistons (flat top) make sure you have 1971-1979 cylinder heads with no less than 90 CC combustion chamber volume or you will forced to use a large percentage of 108 octane racing fuel. The alternative would be to machine a dish in the L2359NF pistons. The L2359NF or L2359F pistons are Sealed Power VMS 75 alloy which is a thicker medium eutectic silicon alloy forging. The top of those pistons will take a dish .300"deep x 3.00" diameter.

With no less than 90 CC combustion chambers, and Fel Pro 8518PT head gaskets that have .039" crushed thickness, your 455 engine will have 10.6:1 static compression ratio. That is borderline for 93 octane pump gas with the initial timing advance set where the engine will run best. There may be off the shelf dished pistons available for the 455 engine but they are smog pistons made of 4032 hypereutectic 18% silicon alloy. My 455 engines had 1963 heads with 70 CC combustion chambers and had 11.8:1 compression ratio. I had to use 100% 108 octane VP C-12 racing fuel with the initial timing set anywhere.

Standard 455 Pontiac rings are 5/64" top / 1/16" second / 3/16" oil. The 455 engine has high thrust loading so GM used a 1/16" second ring in an attempt to reduce cylinder wall wear. The 455 SD racing engines used 1/16" top and second rings and the pistons were forged 2618 (2% silicon) eutectic alloy. The forged pistons and 455 SD/RA-IV camshaft is the reason why the team of engineers who developed the optional 455 SD engines were fired in 1975. . The 455 SD engine could not comply with emissions tests mandated by the revised 1970 EPA Clean Air Act, even after it was tested and equipped with the relatively mild 1966 HO / Tri-power and 1969-70 Ram Air III camshaft. The 1/16" rings and the low silicon pistons had too much blow-by before they reached operating temperature. .
01-07-2013 02:02 AM
cobalt327 BTW, those pistons use a 1/16" second ring so a 'normal' Pontiac 455 ring set won't work.
01-07-2013 01:52 AM
cobalt327
Quote:
Originally Posted by blakethechop View Post
http://www.summitracing.com/parts/uem-kb347ktm-060

after some advise for my 455 pontiac .has anyone used these pistons they are 0cc to increase compression.also what are some options for thin head gaskets without having to o ring i really appreciate all the help im getting
cheers blake
I've never used those exact pistons, but KB are OK pistons- just pay attention to any recommendations they may have regarding the top ring gap and piston-to-wall clearance.

Also, the -060 is for a 0.060" oversize piston (Summit's catalog listing makes it look like that p/n is for a standard piston). -030 would be a 0.030" over, etc. So be sure to order the right oversize for your engine. The machinist will need to assess the condition of your block to give you his oversize recommendation.

Then you have to order the pistons and give them to the machinist for him to measure before doing the final hone. The type of ring used (plain, moly, etc.) needs to be known as well so the hone finish is correct for the rings being used.
01-06-2013 08:12 PM
blakethechop
455 pistons and gaskets

ahttp://www.summitracing.com/parts/uem-kb347ktm-060

after some advise for my 455 pontiac .has anyone used these pistons they are 0cc to increase compression.also what are some options for thin head gaskets without having to o ring i really appreciate all the help im getting
cheers blake

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.