Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Wiring Guide for Electronic Ignition Module Install (Igniter)
User Name
Password
lost password?   |   register now

Thread: Wiring Guide for Electronic Ignition Module Install (Igniter) Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-19-2013 12:49 PM
LacieAZ85306
Thanks so much!

I really want to thank you both for all the help/advice. I'm was really hoping I could get it going myself and I probably could if I had more time, more knowledge, and the proper tools. Thanks!
01-19-2013 12:38 PM
T-bucket23 I have more than once seen a bad cap on those keep them from starting and running.
01-18-2013 06:18 PM
LacieAZ85306
Thanks

Thank you. I was pleased that was the order that I had them in. Unfortunately, it still didn't start. I checked and I don't have a spark. I am going to get a mechanic to help me at this point. Thank you so much for your help. ~Lacie
01-18-2013 02:24 PM
68NovaSS Try this link to see what those wires connect to and what they should test read.

Relocating Ignitor (ICU / ICM) - Honda-Tech

I read the blue wire is tach, white is neg -, blk/yellow is ign.
01-18-2013 12:46 AM
68NovaSS If you can't identify the distributor and look it up, looking at the OEM wiring colors, looking down on it with the three connectors at 12 o'clock and one around the corner to the left, I would connect the black/yellow on the center spade, the blue/white to the left spade, these appear to be correct. That leaves the green and black, if I had to make a choice, I'd put the green around the side where it calls for blue, and the black where the brown goes, to the right of the black/yellow. See if it'll start. If not, swap the last two... Can't get any more back yard than that!
01-17-2013 10:21 PM
LacieAZ85306
Wiring Guide for Electronic Ignition Module Install (Igniter)

'89 Honda Civic


I'm replacing the Electronic Ignition Module (Honda Part Number: Igniter unit kit 06302-PT2-000) inside the distributor.


I do not know how to reconnect the wires. The Igniter has 4 prongs (see pic).


http://i1303.photobucket.com/albums/...pscd5f4aee.jpg




I have 4 wires: 1.Green 2.Black 3.Black w/yellow stripe 4.White w/blue stripe (see pic)


http://i1303.photobucket.com/albums/...ps7997b756.jpg
http://i1303.photobucket.com/albums/...psb5f48676.jpg




These colors do not match the colors in the Honda manual. I read on other forums this probably means the distributor is an after-market.


I need to know which wire connects to which prong. I have searched the web and repair manuals. Does anyone have any idea?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:10 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.