Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Thermostat on wrong end
User Name
Password
lost password?   |   register now

Thread: Thermostat on wrong end Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-21-2013 04:37 AM
joe_padavano
Quote:
Originally Posted by warrick View Post
If I would tap and thread the heads at the bell housing area and use a remote thermostat housing there what would happen to the temp [hot spots]of the enigne if any. I know I would have to do some thing at the front to get air out because of the tilt of the engine?
Most engines circulate coolant from front to back in the block then from back to front in the heads. Your plan runs the risk of overheating the front of the heads.
01-20-2013 07:37 PM
warrick I'm building a gasser type car like dad ran but would be a street/strip use car to take to shows. Was looking at putting radaitor in trunk with electric fans ,55 GPM electric remote water pump. Was thinking of running a 5/8 or 3/4 line out of the rear of each head to a remote thermostat housing like the ones on blower intake. This is to just hide as many lines as possible. Still going to put water into the engine up front, but have been told that I could go into the center of the block on both sides also like some sprint cars are set up. Will be running small block chevy with a 6-71 blower.
01-19-2013 09:34 PM
hcompton A simple tapped screw with a seal will allow bleed from multiple points if need be.

But not sure why you would want something like that. The water inside the head may be at an uneven temp on that part of the head. If you have a hot spot you may just want to run tje heatwr line out of that area and back to the pump that will pull fresh water into the hot area.

You may need to machine the head with a small lip for the thermostat seal. Also two thermostats do not work. But you can use several small orifices and run and open system. Keeps fluid moving across all surfaces if done right but usally getting the water in the raditator cold enough is all that is needed. Unless this is a mid engine build up. Big alum rad and good pump should sort it out.
01-19-2013 09:16 PM
warrick
Thermostat on wrong end

If I would tap and thread the heads at the bell housing area and use a remote thermostat housing there what would happen to the temp [hot spots]of the enigne if any. I know I would have to do some thing at the front to get air out because of the tilt of the engine?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:48 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.