Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> cam replacement
User Name
Password
lost password?   |   register now

Thread: cam replacement Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-31-2013 08:46 AM
Mr. P-Body That cam is not suited for Cleveland 4-V heads. Not nearly enough duration to make it "work". The car will run MUCH better across the range with 2-V heads (that cam). Are they '70 ("quench") or '71-newer heads?

4-V heads are not really the hot lick for a street engine. We get much more "usable" power (in the operating range of a street engine) with 2-V heads, with large valves installed. No porting necessary, just a little "blending".

The strong point of the Cleveland 4-V is it's ability to rev. With only 218 @ .050" lift, RPM can't approach the sweet spot. BTW, it's better to list the "@.050" duration for a semi-accurate comparison to other cams.

Cleveland heads, not unlike BBC heads, "like" more lift than the average. With the 4-V heads, you should have a minimum of 230 @ .050" and .550" lift, to make the heads "work". You should also have at least 6 degrees more duration on the exhaust side. Clevelands are exhaust-impaired.

An open-plenum works very well for high-rev engines. For that cam, I agree, a dual plane (like Performer) is the better choice, but again, we're back to "which heads?".

IMO, Cleveland is far and away the best small block Ford for high-end performance. Apparently Robert Yates agrees... Built correctly, Cleveland is a GREAT engine.

Jim
01-30-2013 03:13 PM
33Willys77 Taking a wild stab (not knowing anything about the motor) - a good dual plane intake and a 600 maybe a 650 cfm carb.
01-29-2013 12:25 AM
techinspector1 You cannot intelligently choose a camshaft for a motor without knowing the static compression ratio of the motor.
01-29-2013 12:13 AM
vinniekq2 post the parts and see who says what and why.Post your expectations
01-28-2013 10:15 PM
jabuitron
cam replacement

I am replacing the cam in a 351c 4v with a
High Energy 268H Hydraulic Flat Tappet Camshaft & Lifter Kit
Lift: .494''
Duration: 268
RPM Range: 1500-5500
Part Number # 249-CL32-221-3

How do I make sure my intake and carb match up andwork well with this type of cam.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.