Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 700r4 Checkball
User Name
lost password?   |   register now

Thread: 700r4 Checkball Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-06-2013 06:56 PM
Kawabuggy 81 Chevy you stated "you have the early valve body with transfer tube & aux. VB"... So, you have TWO holes above the 1-2 sequence valve on the VB????????? That would indicate an early (82-early 86 non-aux. VB's) valve body.

While it is possible (I've seen it before) it is more likely that you have a single hole/late/auxillary valve body.

The pic that Crosley posted, you can leave out the check ball closest to the leading edge. Leaving it out will give a slightly more firm reverse apply. So slight you probably won't even notice a difference.
03-04-2013 03:12 PM
81chevycamino Awesome thank you!!! This rebuild has stalled out hopefully I can get motivated again!
03-03-2013 04:11 PM
Crosley Check balls near front of early v-body, located in the v-body.

Should be witness wear marks (shiney smooth around the ck ball holes) on the separator plate too

03-03-2013 01:42 PM
81chevycamino I do...I have the early valve body with the transfer tube and aux body. I know the check balls I lost were near the front of the seperator plate.
03-03-2013 10:19 AM
Crosley photo of late design 700r4 main v-body. Crude deal photo, sorry. Could not find my other photos. Computers come & go, so do the photos

Look in the yellow square. One hole , to the left of that hole is a flat spot.... that is late design v-body.

IF you HAVE two open holes there, that is an early design v-body

03-03-2013 09:57 AM
Crosley In mid 1987 GM built some weird combos on the 700r4... early 700r4 had no aux v-body and transfer tube...

then they used the early design main v-body with the aux v-body and transfer tube...

then late 1987 they used the updated main v-body with aux v-body and transfer tube.

Different check ball locations per main v-body design and aux v-body or not. Gm was trying to act like Ford or something in 1987 with the 700r4 transmittin
03-03-2013 05:49 AM
123pugsy Relax about the check balls. I can get you that info or you can pick up a 700R4 rebuild manual from ATSG.

Are you doing a full rebuild?
If so, you won't need the check balls until near the end. If you have 2 now, pickup 5 more when you get your kit. You can leave the large one out, so they will all be 1/4'' diameter.

Getting the springs compressed will be a priority before the check balls.

BTW, your response of having an early 87 and also having an aux valve body don't jive. Was there a tube from the oil pump to the rear valve body?
This affects the positions of the check balls.
03-02-2013 06:55 PM
81chevycamino I need to know where they go between the valve body and the seperator plate.
03-02-2013 04:24 PM
123pugsy The check balls probably fell out during disassembly. Pickup how many you need when you get your kit.

You can make tools if you have welding equipment and some chunks of metal laying around.
03-02-2013 03:35 PM
81chevycamino ....I still need help....
01-31-2013 06:31 PM
81chevycamino early and yes it has the aux
01-31-2013 06:05 PM
Crosley Slight changes for check ball locations : 1987 is a mid year change on the 700 trans. Do you have early or late design 700r4?

Does the trans have an aux v-body?
01-31-2013 01:27 PM
700r4 Checkball

I've searched everywhere for my answer! Im rebuilding my early 87' 700r4. I took the valve body loose and there were one or two check ball between it and the separator plate. I don't know where they went. Can anyone help please! Also, does anyone have a trick for compressing the spring things to get the snap rings on without the $200 special tool?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:16 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.