Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Isky 264 Mega for this combo
User Name
lost password?   |   register now

Thread: Isky 264 Mega for this combo Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-04-2013 05:58 PM
1971BB427 That's a great cam, and perfect for a cruiser, and should perform well right off idle to probably 5,000 rpm's. Nice to see someone choose a realistic cam that works, and not get all crazy on huge lopey cams to get a certain sound, but no performance.
02-03-2013 02:07 PM
Originally Posted by vinniekq2 View Post
thanks for that info. I was not sure the 165 darts flow well or not.

Vinnie, according to the Dart catalog the Iron Eagle SS's flow 221 cfm at .400" lift on the intake, 136 cfm at .400" lift on the exhaust, 232/138 at .500" lift, so intake flow is comparable to GM vortecs, but, like GM vortecs, the exhaust is rather poor in flow compared to the intakes. With an exhaust flow of 61.5% of intake flow a split pattern cam would be very helpful. The 180cc and larger port Iron Eagles have a much better exhaust/intake flow ratio. They're around 70-71%.
02-03-2013 12:35 PM
vinniekq2 biged36
thanks for that info. I was not sure the 165 darts flow well or not.
02-03-2013 11:00 AM
BigEd36 According to Dart literature the Iron Eagle SS heads exhaust flow is 61.5% of the intake flow, so if using those heads I would use a split pattern cam with a little more on the exhaust side. Consider the Isky 264/270 Mega cam or something like the Howards #112571-12, 269* intake, 279* exhaust, 215*/225*, .455"/.465", 112* LSA 108* ICL, 1200-5500 Good idle, Strong low & mid-range torque & horsepower.
02-03-2013 07:50 AM

Cam is a fairly good choice. Rear gears are less then optimal as you know.
02-03-2013 01:35 AM
tresi My very first hotrod had a similar combo. It will work ok but it will like a little more gear but it will work until you can afford the gears.
02-02-2013 11:51 PM
vinniekq2 check out those heads before you use them.I think the flow numbers are low
02-02-2013 12:46 PM
ssmonty I've got a 350 with a HE260 cam (212@0.050"), stock convertor, 3.73 rear, performer intake, 600 VS Holley, Tri-Y headers, 200R4 trans.. It pulls 15" vacuum at 650 rpm idle. Runs great from idle to about 5200rpm with good throttle response(3.73 might have something to do with that).
I didn't figure the CR back in the 1980's when it was built, but it was supposed to be around 8.8:1. The heads came from RHS back then and were stock rebuilt cast iron w/76cc chambers with pocket porting/bowl blending(?port cc).
Your cam is just a little bigger, and with 108 lsa vrs the 110 lsa mine has, I'm thinking you may have just a little less low end/idle vacuum.
I'd say it was a good choice except for the rear gear being just a bit too high.JMO
02-02-2013 12:32 PM
6sally6 Should be a good fit! Compression is high enough....duration is not too big and the "Isky" trademark 108 LSA will give it a good lick at idle. I like it!!
02-02-2013 06:36 AM
GMC boogie
Isky 264 Mega for this combo

Thinking about this HFT camshaft for a mild 355 in a '72 Chevelle.

Dart ss 165 iron heads with 72cc chambers
6cc flat top pistons
9.3:1 CR
Weiand 8125 dual plane manifold
Quadrajet carb
2.73 axle ratio
1 5/8 headers with 2 1/4 dual exhaust

The cam specs are 214/214 at .050 264/264 at .007 .450/.450 lift with 1.5 rockers and has a 108 LSA

Obviously not a drag car with the 2.73 axle ratio. The car is just meant to be a nice cruiser with good drivability and low-mid torque.

Cam looks like a good match. Any thoughts?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:26 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.