Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Gm piston number what does it mean
User Name
Password
lost password?   |   register now

Thread: Gm piston number what does it mean Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-04-2013 04:25 AM
firebird7980 Thank you
02-03-2013 08:44 PM
BigEd36
Quote:
Originally Posted by firebird7980 View Post
The 60 is under the the rest of the number . What do you mean ch of 1.56
CH - Compression Height - is the distance from the center of the piston pin to the top of the piston. 1.56" is the compression height of a standard 350 piston. Many aftermarket pistons are what's called "rebuilder" pistons, they are only 1.54" compression height, or .020" shorter. The reasoning is that it's assumed when the engine is rebuilt the block will be decked, so making the piston shorter will keep the piston deck height (the distance the top of the piston is below the top deck of the block) will be the same. If your engine is rebuilt using "rebuilder" pistons and the block is not decked, now your pistons will be .020" further "in the hole" (down in the cylinder). That will lower your compression ratio, and add .020" to the squish/quench height (distance from the top of the piston to the cylinder head) which makes an engine more likely to have detonation problems or require higher octane gasoline to prevent the detonation.
02-03-2013 07:11 PM
firebird7980 The 60 is under the the rest of the number . What do you mean ch of 1.56
02-03-2013 01:33 PM
cobalt327 I'd tend to agree w/BigEd36- Silvolite Pistons, bottom of the page. Two possibilities are shown, one has a 0.070" deep dish, the other a 0.080" dish. Both are available 0.060" over. The numbers shows up under "O.E. Casting No."

If these are original pistons, they should have a CH of 1.56". But if they're aftermarket replacements, they're prollably going to be the shorter rebuilder type.
02-03-2013 12:26 PM
BigEd36 From searching online I can't find much about that casting number, but Silvolite shows a piston replacing that part number, it's either 11 or 13 cc dish piston, Silvolite's version is 1.54 compression height instead of the factory 1.56 so they would be considered "rebuilder" pistons that will give you .020" more "in the hole" or piston deck height than standard pistons. The 60 at the end of the number probably means they're .060" overbore sized.
02-03-2013 09:13 AM
vinniekq2 contact fbird88 I think he has used these pistons
02-03-2013 05:54 AM
firebird7980
Gm piston number what does it mean

I have a gm piston. just try to figure out what the numbers on the bottom of the piston means 3991476 60 thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.