Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Help with Push Rod Length SBC
User Name
Password
lost password?   |   register now

Thread: Help with Push Rod Length SBC Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-09-2013 04:32 PM
Landshark928 Thanks guys! I wanted scorpion but they only have .083 thickness in the 5/16th.

I double checked the Manley with their catalog and other sites. Good to go at .120"
02-09-2013 02:47 PM
Richiehd I ordered my pushrods from Scorpion, they have any length you want. Also with a 1.65 rocker you will have a wider pattern, centered is good
02-09-2013 02:26 PM
engineczar No problems as the oil hole at each end is still smaller than it is in the center. The stiffer the pushrods the better. .120 wall will work well. One thing to clarify is that the description on the Summit site says .080 wall. I'm not near my Manley catalog to check.
02-09-2013 12:16 PM
Landshark928 Got the dial indicator on this morning. Seems like 8.150 is the ticket. Going to order .120 wall 5/16th rods instead of 3/8ths so I don't have to change my guide plates. Any issue with thicker walls as far as oiling? Can they be too thick?

Looking at these Manley rods.
Manley Pushrods 25242-16 - SummitRacing.com
02-07-2013 09:08 PM
496CHEVY3100 I had to throw out my pro comp puchrods POS .replaced with trick flow mine is BBC had to go .250 longer becacse of aluminum heads TF. .Did not save any money as i had to buy 2 sets,buy a good set first time save money i did have to clearance bottom of comp cam rollere rocker to clear my springs.
02-04-2013 09:57 PM
Landshark928 Thanks guys! I will get a dial indicator this weekend and see which length gives the most lift.
02-04-2013 01:12 PM
ap72 B I N G O and bingo was his name-o!

engineczar gave you a foolproof way of checking, the one that gives you the most lift should also give you the smallest pattern and be the correct one- BUT the pattern may not be quite centered, to fix that you'll need to move the rocker stud which can be a pain in the *** and usually not worth it.
02-04-2013 11:49 AM
engineczar Putting a dial indicator on the retainer which pushrod length gives you the most lift?
02-04-2013 11:25 AM
oldbogie
Quote:
Originally Posted by Landshark928 View Post
Trying to dial in my push rod length.

Using the Comp Cams checker 8.150" gauge centers the wear pattern best, however the wear pattern seems pretty wide. Almost from 1/3 inboard to 1/3 outboard.

Also 8.150" seems rather long to me for a solid roller cam in a SBC.

Dart block zero decked.
Lunati Voodoo solid roller with 1.65 scorpion rockers. .660 adjusted lift .016" lash(60133 cam, I think it's a .9" base circle.)
Lunati solid roller lifters
Airwolf heads with +100 valve

Here are pics of the pattern with a 7.900 and 8.150 push rod. Pattern is more center and smaller with the 8.150. Should I try 8.200 to get it perfect. I was worried it seems too long already.








Also note the cheap Pro Comp 7.900" push rods I have do not match up to the Comp Cams checker. When both are set for 7.900 the Pro Comp is much shorter than the checker. Since it uses gauge length I would have thought it would be a tad longer. Guessing the Chinese crap is like playing the lottery?



Here are the push rods I am thinking of ordering:
COMP Cams Hi-Tech Pushrods 8478-16 - SummitRacing.com

8.100"- 3/8" 0.135 wall
or
8.280"- 3/8" 0.135 wall

So before I order, am I missing something? Seems like my Lunati lifters may be standard flat tappet height and not stock roller lifter height?
The 8.150 looks good to me, try to get push rods as close to that as you can, if not have a custom length made for you, nothing stock about your engine so expect the unexpected.

Bogie
02-03-2013 09:08 PM
Landshark928
Help with Push Rod Length SBC

Trying to dial in my push rod length.

Using the Comp Cams checker 8.150" gauge centers the wear pattern best, however the wear pattern seems pretty wide. Almost from 1/3 inboard to 1/3 outboard.

Also 8.150" seems rather long to me for a solid roller cam in a SBC.

Dart block zero decked.
Lunati Voodoo solid roller with 1.65 scorpion rockers. .660 adjusted lift .016" lash(60133 cam, I think it's a .9" base circle.)
Lunati solid roller lifters
Airwolf heads with +100 valve

Here are pics of the pattern with a 7.900 and 8.150 push rod. Pattern is more center and smaller with the 8.150. Should I try 8.200 to get it perfect. I was worried it seems too long already.








Also note the cheap Pro Comp 7.900" push rods I have do not match up to the Comp Cams checker. When both are set for 7.900 the Pro Comp is much shorter than the checker. Since it uses gauge length I would have thought it would be a tad longer. Guessing the Chinese crap is like playing the lottery?



Here are the push rods I am thinking of ordering:
COMP Cams Hi-Tech Pushrods 8478-16 - SummitRacing.com

8.100"- 3/8" 0.135 wall
or
8.280"- 3/8" 0.135 wall

So before I order, am I missing something? Seems like my Lunati lifters may be standard flat tappet height and not stock roller lifter height?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.