Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Preparing rust for paint
User Name
Password
lost password?   |   register now

Thread: Preparing rust for paint Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-07-2013 06:46 AM
Chevymon
Quote:
Originally Posted by hpete View Post
All the above is good advice, but urine is a salt not an acid. Once you get the paint job done if you'll rinse it from time to time with a mild acidic detergent it will last much longer.
My mistake, thank you for the correction.
Apparently the vegetarian diet has something to do with it.

Urine pH: Urine pH is typically acidic in dogs and cats and alkaline in horses and ruminants (cattle, deer, sheep, buffalo, ect).
Merck Veterinary Manual
02-06-2013 08:28 PM
hpete All the above is good advice, but urine is a salt not an acid. Once you get the paint job done if you'll rinse it from time to time with a mild acidic detergent it will last much longer.
02-03-2013 12:57 AM
demarques_191 Any rusted panels must be sanded down to the max you can to where all rust is gone and not seen again.... Sand it with 80 grit or a wire wheel in tight spots... blow dust, dirt, residue off, clean it with some kind of metal cleaning agent, even though some people use thinner to make sure the metal is properly clean so the primer can adhere....Then use a expoxy primer because it has the most bite to the bare metal than any other bare metal treatment... give it some flash time between coats and u dont have to apply it heavy either, put it light to medium coats... 2 coats is fine, get it covered completely but make sure your gun is setup properly to where you have enough material coming out but not too much (this is done from adjusting the fluid nozzle in and out) then you have about a hour window to shoot your topcoating primer of choice... (primer filler, polyester, etc) you can actually spray color over the epoxy primer
01-30-2013 02:55 PM
painted jester Sand blasting is good! I still use etch, and lately epoxy sealer instead of the zink primers!
Auto paints dont stand up! An Industrial machine enamel paint used on laths and presses and mills, and industrial motors will! On sulfuric acid reactors The motors still look good after years of use with acid slashing on them every day! Zinc Chromate primer if you can obtain it !Zinc Chromate is a corrosion resistant agent that is added to certain coatings. Even today, chromate finishes including Zinc Chromate provide superior corrosion resistance. ( Zinc Chromate is highly toxic) it protects the surface from proliferation of organic matter, acids, salt,etc. Its in a lot of Machine finishes!

I take for grated this is a working trailer not a weekend horse show show piece! And your on a budget and want it to last a while but be able to take the abuse horses can dish out and working around your stables!

Jester
01-30-2013 04:43 AM
Chevymon
Quote:
Originally Posted by thinwhiteduke View Post
Sandblast it, you need clean, 'unadulterated' metal...

Duke
Media blasting is the only way to make it last, wire brushing polishes the rust and hides it. And urine is acidic so you need epoxy primer and a good urethane top coat to stand up to the acid. If you go quick and cheap then a cheap repair is all you will get.
01-29-2013 09:40 PM
thinwhiteduke Sandblast it, you need clean, 'unadulterated' metal...

Duke
01-29-2013 09:24 PM
cutthroatkid So will the primer&paint start to peel immediately if I shoot it the way it is?
01-29-2013 09:21 PM
painted jester
Quote:
Originally Posted by cutthroatkid View Post
So I'm working on a horsetrailer..I know hardly a hot rod but I need some advice.I hit it with a wire brush&then sanded it down smooth with the D/A Im wondering if after I shoot primer&paint will that seal it or will it just eat through the paint?I'm open to suggestions.Thanks
Horse trailers, The urine, and manure impregnate the metal in all the blind spots and inside the tubes Ive painted many! I haven't found much that will stop it! The good products have been changed (E.P.A.) A good acid wash and triple rinse Etching primer on all bear metal, seal with a top line epoxy and shoot with a good industrial machine enamel ( colors are limited) That will take abuse and stand up against the animal excrement! They don't piss on everything but in the heat it evaporates and condensates and impregnates cracks and crevices even over head! The Bison trailers are the worst to rust in my opinion!

Jester
01-29-2013 08:52 PM
cutthroatkid
Preparing rust for paint

So I'm working on a horsetrailer..I know hardly a hot rod but I need some advice.I hit it with a wire brush&then sanded it down smooth with the D/A Im wondering if after I shoot primer&paint will that seal it or will it just eat through the paint?I'm open to suggestions.Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.