|02-12-2013 05:57 PM|
check out my pics @1979 malibu classic in the works
in the albums
|02-12-2013 05:34 PM|
the rods came with eagle spec esp-13010030 i think stock length 5.7 ? forged 5140 i beam
i dont rember the part number of the gasket .thickness was on my machine shop invoice
as far as the studs yes on the washers that came with them and arp sealant (white tube ) under pressure they leak .today I talked with arp and they tell me remove all the water from the system remove one stud at a time blow out with compressed air squirt brake parts cleaner in the hole blow out again clean the threads and load the threads up with a lot of arp or permatex ptf and retork .
do only one at a time .What a pain in the *** !!!!!either the product works or not i say NO .I will b changing to permatex
|02-12-2013 05:32 PM|
|F-BIRD'88||It will work fine for pump gas. For a girlie cam.|
|02-12-2013 05:15 PM|
|macrobert68||yea i saw the cam requires 11-1 and im around 10.3-1 whats going to happen ?|
|02-12-2013 12:27 AM|
I have a couple of questions for you. What length connecting rods did you use? The Cometic head gaskets you used is C5249-030 the part number? If not post the part numbers you used. When installing the head gaskets did you use any type of sealer on them. Also did you install washers under the nuts on the head studs?
|02-11-2013 09:49 PM|
|macrobert68||I did get alot of help with direction from my machine shop teck|
|02-11-2013 09:48 PM|
howard cam number
|02-11-2013 09:38 PM|
2800 stall in th400 unsure what rear end to use .I was thinking gm 12 bolt 410
What do u think? Mostly street car some track time gotta find out what it will do
|02-11-2013 07:24 AM|
Static CR is around 10.3, but my concern is if the block hasn't been decked, the quench distance is ~0.055".
Fill in the blanks and a guess could be made.
|02-10-2013 03:54 PM|
|hpete||Fbirds right about the carbs. I don't have time to do the math but I'd bet the compression will be low for the cam.|
|02-10-2013 03:52 PM|
Using the right springs and heads that cam will make power to about 6,500, and you will need some stall if it's an automatic.
Poser girlie-man motor?? Now that's funny...
|02-10-2013 03:15 PM|
They are T bucket cruiser-poser carbs.
Get real 650+cfm DP carbs for it.
Edelbrock 750's work well too.
They make engine test dynos to determine HP.
Get some real carbs and dyno it.
The HYD cam will run out of steam and limit power and rpm.
This is a poser girlie-man motor.
|02-10-2013 11:10 AM|
Ill be in the garage today rebuilding my second holly today so i wll check back later thanx everyone.
|02-10-2013 11:06 AM|
I like this forum very helpful.Here is a question for all u
hotroders out there
What are the thoughts of the amount of hp and compression from this build?
1974 400 block machine shop to .030 over >406
line bored shop balanced on newest machine
(shop tells me its the newest ballancer on the market )
(now i wish i would of went forged)
flat top pistons with two releif cuts
howard cam .555/298/308/110hyd roller
crane roller rockers (gold pro race 1.5)
dart shp 202/180 72cc on stock deck height
comtiec gasket compressed 0.30
weiand tunnel ram with twin 4160 450 cfm carbs
holly hp mech fp 110gph
msd plug and play msd wires msd coil
Super Competition, Full-Length, Steel, Ceramic Coated, Chevy Headers
|02-10-2013 02:14 AM|
|F-BIRD'88||Some SBC exhaust rocker studs go into water and need sealing too.|
|This thread has more than 15 replies. Click here to review the whole thread.|