Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 12 bolt spider gears binding
User Name
Password
lost password?   |   register now

Thread: 12 bolt spider gears binding Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-16-2013 09:52 PM
prostreet6t9
Quote:
Originally Posted by lmsport View Post
There are different thickness shims for the axle side gears.
I know I have a big box of them, so try to find a shop that has some.
The Aftermarket Side & Spider kits Don't come with Selectable thrust washers.
02-15-2013 03:51 PM
painted jester Tights good, loose is bad !! You installed new spiders & shims they need to be broke in, drive till hot, let cool , drive till hot let cool again, Do this several times and the gears will break in with a good pattern!

Jester
02-15-2013 02:24 PM
lmsport There are different thickness shims for the axle side gears.
I know I have a big box of them, so try to find a shop that has some.
02-15-2013 12:33 PM
matt2491 Thanks guys for the advice!

I just called Superior and they said that it is good that the gears are tight. The guy said its better they be too tight than too loose. Does this sound right to you guys?
02-15-2013 12:20 PM
rick 427 Thats good advice..and now that you have some knowledge now,I would still call Superior and talk with them about this,and hopefully be able to get your money back if it doesn't work out.
02-15-2013 12:13 PM
big gear head Probably should have replaced the whole differential instead of just replacing the gears. GM usually makes some changes in the differential case when they change the axle splines or other parts. There are several versions of cases for the 7.5 and 8.5 rear ends because of minor changes that GM made when they changed axle splines. You can not run 28 spline gears in a 26 spline case in the 7.5 and you can not run 30 spline gears in a 28 spline case in the 8.5. You can not run 30 spline gears from the '90 to '98 case in the 30 spline '99 to current case in the 8.5. I would say that the inside dimintions of the case are not the same between the 17 spline version and the 30 spline version. Do not run it without the thrust washers. The gears will eat into the case.
02-15-2013 12:07 PM
matt2491
12 bolt spider gears binding

Long story short, I need to replace the spider gears in my open diff '64 truck 12 bolt because I am converting from 17 spline to 30 spline axles. I bought a kit made by Superior that includes both side gears, spider gears, and thrust washers to go behind each gear. However, when I have it all installed in the carrier, the gears are virtually binding against each other. If I stick an axle in and try to turn the diff, it takes some effort and the gears are very notchy because there is zero play between them. Its like the thrust washers are too thick, especially the conical ones behind the spider gears. Without them in place however, the gears seem too loose.

I should note that the original spider gears did NOT have thrust washers behind them, but the side gears did.

Now I'm pretty confident this 12 bolt hadn't been abused. The whole truck is in good shape, and everything looked really good when I opened up the diff. The main ring & pinion backlash is perfect, the teeth on everything looked perfect, etc etc. So I don't think the carrier is warped or anything like that.

Anybody have any ideas about this? How are the spider gears supposed to feel? What kind of play is acceptable?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.