Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 99 ranger tranny rebuild - what special tools are needed?
User Name
Password
lost password?   |   register now

Thread: 99 ranger tranny rebuild - what special tools are needed? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-19-2013 07:25 AM
joshp83 i mainly use transgo kits in the shop but there 4r55/5455 kit is pretty crappy compaired to the superior kit for this unit
the pro king kits are not bad auctually a reboxed transtar kit they dont come with thicker steels to set clearance
i use buy kits directly from dacco or transtar u can get a atsg book pretty resonable it would be usefull
02-18-2013 10:08 PM
maverickmechanic13 Thanks for the input fellas. However - your help causes more questions:
-any rebuild kit better than the next? i can easily get get my hands on a pro-king kit... but through my work i can only get a kit for a 2wd model... since i have no book or manual abut the tranny ... any input?
-transgo is a no-go in this case? ive used trans go kits before... pretty impressed with their stuff. Liked what it did in my Z28 and other various projects i stuffed their kits in.
-again... literature on the matter? any manuals better than others?

Thaks a bunch again.
02-18-2013 08:16 PM
joshp83 99 should be a 5455 e with a 4.0 there not a bad unit to build make sure you replace the servos on the side of the case i aways use the zc cover and pistons on both the center support is known for wear use a superior shift kit do not use a transgo kit in this unit get a large ratio pressure regulator valve they make thicker steel clutch plates to get the clearances tighter becareful cleaning the valve body it has many clips that will fall out also use a a external trans cooler
02-18-2013 08:03 PM
Crosley Get bandaids .... the edges of that narrow deep case can be sharp and trim up your arm skin.

Check the servo pin bores in the side of the case, they like to wear out badly sometimes
02-18-2013 10:38 AM
rick 427 The only specialty tool you will need is the pump alignment kit,which consists of a plastic outer ring,and a plastic hub that re-inacts a converter hub.The clutch drums come apart like a 400,which you are familier with allready.I use my seal puller to remove the center support.You will see what I'm talking about when you get to that point in the disassembly.Everything else,you have in your toolbox....you can get the pump kit[and everything else you need] direct from Transtar in Bedford....alignment kit PN is T-0168K....upon reassembly,you will need to find a plastic sleeve that compresses the new rubber center support rings. They come installed on new replacement supports.I haven't seen them for sale anywhere else. A trans shop,or Cleveland transmission,will prob have one laying around to sell or give you.
02-17-2013 06:44 PM
maverickmechanic13
99 ranger tranny rebuild - what special tools are needed?

Hello everyone

Got a 99 Ranger (4.0 4x4) that lost reverse. Absolutely no reverse whatsoever. From all preliminary diagnosis it seems the band failed inside the tranny. Apparently common problem for these 4r44/55e trannys from my research so far. So... a tear down and rebuild is in order.

I have rebuilt a few trannys (all of them actually GM trans'... i am GM tech), installed reprogramming kits and shift kits, all without a problem so far. I have a ton of books on 700r4/4l60s, th 350s, 400s etc... but no info so far on a ford trans. Anyboy have any recommendations on a good book for rebuilding one of these bad boys? Most importantly, any special tools these trannys require? As a side note, any of you guys have any experience with these units?

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:42 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.