Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Header Gaskets
User Name
lost password?   |   register now

Thread: Header Gaskets Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-21-2013 04:19 PM
lakeroadster I did some searching here on the Hot Rodders site a while back looking for header gasket recommendations and found this thread:

That lead my to use stock manifold gaskets on my headers. If you are running stock heads, with stock port configurations, they work just fine right out of the box.

Not sure though how they will work with the fuels you are using.

Here's the gasket set P/N's I ended up using:

Gaskets installed:
02-21-2013 04:14 PM
Originally Posted by e073785 View Post
What is the best heater Gaskets For Finder wlll headers with Plates, it burning thru in the center flange. I am running methnane or alcohal as fule.

Douglas Ray
I run copper, aluminum or carbon/carbon especially with alky. That stuff (alky) burns slower than gasoline which puts a lot of temp into the exhaust. You may want to play with more ignition lead and/or more compression to force the burn to get over with before the exhust valve opens. You may find that an external coolant hose from the pump ears into the heads under and between the paired exhaust valves will help take some heat out of this spot. The head kind of warps in this area which makes life as an exhaust to header or header adapter gasket quite a bit tougher than on gasoline motors.

02-21-2013 12:43 PM
thinwhiteduke I have no trouble with those perforated metal composite type that they supply in the gasket kits. I put high temp silicone (smear) both sides, nip em up most of the way, let it set and fully tighten. Check when cold 3 or 4 times and then occasionally. Keep em tight.
But the MOST IMPORTANT thing, make sure the flange on the header is STRAIGHT!!! Mine had a .100" bow in the middle, no way I could get em to seal. So I filled it up with weld, the ground it, belt sanded it, check with straight edge until it was straight. .....No leaks now!

I feel that so long as your surfaces are straight, pretty much any type gasket would do the job. Keep a check on the bolts....

02-21-2013 12:30 PM
Header Gaskets

What is the best heater Gaskets For Finder wlll headers with Plates, it burning thru in the center flange. I am running methnane or alcohal as fule.

Douglas Ray

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:09 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright 1999 - 2012. All Rights Reserved.