Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Pushrod length
User Name
Password
lost password?   |   register now

Thread: Pushrod length Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-31-2013 12:09 AM
cdminter59
Pushrod length

This adjustable pushrod checker should get you the correct length pushrods. COMP Cams Hi-Tech Pushrod Length Checking Tools 7702-1 - SummitRacing.com. The stock flat tappet pushrods are 7.800". OEM roller cam uses 7.200" pushrod. Retro roller cam uses 7.300" pushrods. Most aftermarket heads use +.100" longer pushrods. This pushrod checker is 6.800" - 7.800" so it covers them all.
03-18-2013 07:41 AM
hcompton
Quote:
Originally Posted by 383SBC View Post
Looking for a little info concerning push rod length. Assembling a 383 sbc that has had both the heads (AFR) and block resurfaced. How much was taken off I am not completely sure of but I do know it was a minimal resurface cut. I am also using a very thing gasket, FelPro 1094 at 0.015" compressed thickness. The last kicker is that I will be running a retrofit hydraulic roller cam with retrofit hydraulic roller lifters. Now these lifters are higher than the hydraulic flat tappets so I have read that the use of a shorter pushrod is mandatory. Also the fact that I have had both the block and head resurfaced and running a thin head gasket would mean I would need a shorter pushrod yet. I will most likely end up buying an adjustable pushrod to verify proper pushrod length, I just don't know what numbers I will be looking at and which adjustable pushrod I will need?

I got a set form amazon had both sizes of adjustables and was very cheap. Dont buy really expensive ones you will use it once and shelf it so go cheap. they all work the same. I think crane or comp both make a pretty cheap one.

Crappy thing is they make them right outside the size you need. one is 7.2 the other is 7.2 and above. Not sure why they dont make one that is 6.5 to 7.5 but i purchased two so maybe thats the reason.
03-18-2013 01:39 AM
cobalt327 If the lifters are the same as the OEM hydraulic rollers, you'll be in the 7.2" range. IIRC most others are in the 7.3" range. But Crane uses very short p-rods for some of their hydraulic roller lifters and cams (just over 7.00").

If you know the brand of the lifters you can research it from that, or by measuring the distance between the p-rod body and rocker arm, then adding the depths of the cups. This will get you a ballpark figure to work with to make a tool.

Other things that can effect p-rod length is the valve length and cam base circle diameter, so you will need to mock it up once you get a ballpark figure to work from. A couple pages that will help:

Adjusting hydraulic lifters
Valve train points to check
Valve train geometry
Valve spring installed height

Click on image for details on making an adjustable pushrod:


Other homemade pushrod length checking tools at HomemadeTools.net
03-18-2013 01:00 AM
383SBC
Pushrod length

Looking for a little info concerning push rod length. Assembling a 383 sbc that has had both the heads (AFR) and block resurfaced. How much was taken off I am not completely sure of but I do know it was a minimal resurface cut. I am also using a very thing gasket, FelPro 1094 at 0.015" compressed thickness. The last kicker is that I will be running a retrofit hydraulic roller cam with retrofit hydraulic roller lifters. Now these lifters are higher than the hydraulic flat tappets so I have read that the use of a shorter pushrod is mandatory. Also the fact that I have had both the block and head resurfaced and running a thin head gasket would mean I would need a shorter pushrod yet. I will most likely end up buying an adjustable pushrod to verify proper pushrod length, I just don't know what numbers I will be looking at and which adjustable pushrod I will need?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.