Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Marine 454 in a 55'
User Name
Password
lost password?   |   register now

Thread: Marine 454 in a 55' Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-28-2013 05:52 AM
bigalturk1 I changed my mind on that boat engine (I'm told that the engine was sold anyway).
I think I'll buy a rebuild-able car or truck engine
Thanks for your input!
03-27-2013 11:32 PM
NastyRat
Wet 454

Is it a gen 6 454 or an older one. Marine engines are high nickle castings stronger. Should also be 4 bolt mains 330 hp should be big port heads. If it is a late model it will also be a Roller Cam. Will use a little more oil on the street do to the added piston clearance set for marine applications. In my opinion not a bad deal if it is a 96 or newer and complete. The marine set up will make great torque and run good to 5200 RPM's. Has a different cam grind than the truck engine. All late engines are 4 bolt mains. The stock 502 cam would be perfect for a cam up grade if it's a 96 or newer. You can re use the lifters, need to change springs and intake gskt. other gskts are re usable if not damaged. Late model's also require electric fuel pump. Also will not be able to use dist unless it is an older engine.
03-27-2013 07:19 PM
bigalturk1
454

Thanks, I'll hold off for abetter deal, thank you.
03-19-2013 07:56 PM
bigdog7373 $1,700 is a LOT. Look around some more for a better deal. I wouldn't pay more than $1000 for a running 454. Craigslist is where i found my small bock, lots of good deals there.
03-19-2013 05:08 PM
BOBCRMAN@aol.com
Quote:
Originally Posted by bondo View Post
Ayuh,.... That Marine motor is basically a Truck motor of that vintage, with Marine exhaust manifolds, 'n t-stat housing added to it....

The water pump is 'bout the same, but you'll need headers to replace the manifolds...
Ya might want a hotter cam, distributor will run just fine...
Crankshaft bolt pattern is determined by Vintage, 'n is the same as All BBCs..
Water circulation don't change other than the t-stat housin', 'n manifolds,...
'n, Btw, it's a standard Lefthanded motor, yer lookin' at the wrong end,...
Heater outlet/ inlet can be put whereever ya need 'em...

Treat it as if ya yanked it outa a Truck,...
The cam may work great for you. I have a couple of customers that have used marine cams in their BBC's and love the torque.

Yes, just a truck motor with better gaskets. Be careful and get the correct flexplate for the series of BBC. Mark IV and V flywheels look the same but are balanced different.
03-19-2013 05:01 PM
bondo
Quote:
Originally Posted by bigalturk1 View Post
I have a chance to buy a 454 marine engine just pulled from a freshwater boat, for $1,700 (Low hours). The owner says it has 330 horsepower and the cylinder cranking pressure is 180 lbs. in each cylinder (Sounds high).
Not being a Marine mechanic, I was wondering if this would be a good choice to put in my recently purchased 55' Chevy with a Turbo 350 or 400 trans
and a 9" Ford rear-end (3:73). I'm looking for low-end torque, not high-revving horsepower. The water pump and exhaust manifolds need changing, maybe the cam & distributor too. Adding to that the carb is probably set-up differently, but I'm wondering about the back of the crankshaft mating to the flywheel. Water circulation I'm told, may be difficult because of the way marine engines flow (Even though the engine turns clockwise) and what about heater hose outlets.
I'm looking for someone that is sure about these questions... Thanks.
****,.... That Marine motor is basically a Truck motor of that vintage, with Marine exhaust manifolds, 'n t-stat housing added to it....

The water pump is 'bout the same, but you'll need headers to replace the manifolds...
Ya might want a hotter cam, distributor will run just fine...
Crankshaft bolt pattern is determined by Vintage, 'n is the same as All BBCs..
Water circulation don't change other than the t-stat housin', 'n manifolds,...
'n, Btw, it's a standard Lefthanded motor, yer lookin' at the wrong end,...
Heater outlet/ inlet can be put whereever ya need 'em...

Treat it as if ya yanked it outa a Truck,...
03-19-2013 10:28 AM
bigalturk1
Marine 454 in a 55'

I have a chance to buy a 454 marine engine just pulled from a freshwater boat, for $1,700 (Low hours). The owner says it has 330 horsepower and the cylinder cranking pressure is 180 lbs. in each cylinder (Sounds high).
Not being a Marine mechanic, I was wondering if this would be a good choice to put in my recently purchased 55' Chevy with a Turbo 350 or 400 trans
and a 9" Ford rear-end (3:73). I'm looking for low-end torque, not high-revving horsepower. The water pump and exhaust manifolds need changing, maybe the cam & distributor too. Adding to that the carb is probably set-up differently, but I'm wondering about the back of the crankshaft mating to the flywheel. Water circulation I'm told, may be difficult because of the way marine engines flow (Even though the engine turns clockwise) and what about heater hose outlets.
I'm looking for someone that is sure about these questions... Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.