Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Good valve spring compressor?
User Name
Password
lost password?   |   register now

Thread: Good valve spring compressor? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-25-2013 07:05 PM
S10 Racer
Quote:
Originally Posted by Nuck Chorris View Post
I will be doing this on a bench. Is is necessary to get one of these off a tool truck? Mac, Cornwell, Snap-ON? Or just Amazon, Craftsman? What's a decent one?
There is no reason to spend a bunch of money on a valve spring compressor if you have a spare "C" clamp laying around the garage. Here is my compressor I made and have used on BBC & SBC. Much stronger that any that you can buy and will compress any valve spring.
04-25-2013 05:29 PM
ssmonty If your looking to save some money there is one that works well for me after I made a couple of cheap mods to it. Maybe your strong enough to use it as is? (http://www.summitracing.com/parts/otc-4572/overview/) I wouldn't pay much attention to their description, or if you figure out how to use it with the heads installed, show me!
Its similar to the (http://www.summitracing.com/parts/wmr-w89409/overview/) , but seems much stronger, or at least it worked for some roller beehives that the other wouldn't because it flexed too much(jaws spread).
I drilled two holes(1/4") in the handle close to the middle of its width. Got a piece of 3/4" alum bar stock about 12" long that was in the scrap pile at work. Drilled a 1/4" hole in it. Bolted it on and drilled another hole with the hande as a guide. Got a piece of 1" pipe at Lowes for less than $5 to use as an extension. Works great. Albeit a little work, beats spending $150 for something that you only use in a blue moon, at least it was for me.
FWIW,
ssmonty
04-25-2013 04:44 PM
BOBCRMAN@aol.com Depends on how often you will use the compressor.. A very good one is marketed by Lisle and available at auto parts retailers. It will last a long time as long as you are not using it on BBC roller sprngs.
04-25-2013 03:02 PM
Nuck Chorris
Good valve spring compressor?

I will be doing this on a bench. Is is necessary to get one of these off a tool truck? Mac, Cornwell, Snap-ON? Or just Amazon, Craftsman? What's a decent one?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.