Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> door jambs and door fitting?
User Name
Password
lost password?   |   register now

Thread: door jambs and door fitting? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-03-2013 12:58 PM
Windy Thank you Martinsr, and Killer, for the suggestions. I do have the body fastened down solid, but I haven't shimmed anything like I found in the orginal wood frame. I have a background in housing, and the methods used there for adjusting doors, apply to the car also. I can shim a few places and see what it does, as I didn't weld down any parts. I did this because of the fitting session I knew was coming! Hope I can improve it some but it does close anyhow, except for the passenger door where the original owner got hit by something in 1943 lol. I am the second owner, bought it after he died in 1961. TY, Windy.
05-02-2013 08:24 PM
killeratrod martinsr always spells it out perfectly. just figured you would get what needs to be done here.
05-02-2013 08:15 PM
MARTINSR Is the body bolted down solid on the frame? For that fine tuning that body has to be bolted down, not just sitting there and God forbid on saw horses or something. Bending the hinge a little is very do-able. Look at your gaps, if the door is a little down at the back and it's tighter at the top front to the cowl than the bottom you want to bring back the bottom, if the gap is tighter at the bottom than the top at the front you want to bring in the top to raise the rear. Understand? You may want to go straight up by simply raising the whole door, or you may want to bring the bottom back to raise the rear or bring the top forward to raise the rear. Any of these three methods would do the same thing, which one makes the most sense to leave you with the best gaps is the question.


But first be sure that body is bolted down properly. You can even shim the body to the frame to raise the back of the cowl raising the door on many older cars, the bodies aren't that strong and move a LOT. This is without a doubt a perfectly fine way to align a roadster door. With yours I am not so sure, I am thinking it would be a fine way to do it.

Brian
05-02-2013 06:36 PM
killeratrod also maybe a block of wood and a jack and tweek it a little bit
05-02-2013 06:34 PM
killeratrod you need to use some shims.
05-02-2013 05:13 PM
Windy
door jambs and door fitting?

I have a 33 Chevy coup, and the doors are not in line with the latch side, I have replaced the wood on the hinge side with metal and fastened it to the metal inside body frame I made in lieu of the wood there before. It is solid but the doors sag some, need to be lifted to latch well, and they do latch, but they are not perfect at all! Any ideas?
They are about 1/4 to 3/8ths low of perfect!
Ty, for your help in the past also!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.