Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> crinkle spots in base coat
User Name
lost password?   |   register now

Thread: crinkle spots in base coat Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-10-2013 07:20 AM
ggorman Do you recall the fix for the actual paint job?

I've been doing this as a hobby for about 50 years and it never ceases to amaze me how many things can go wrong.

Paint will stick to a car 100 feet away but then peel off in sheets from the car at hand.
05-10-2013 07:07 AM
Crinkled paint.

In the old Mustang factory every couple days about half a dozen cars came out of the paint oven conveyor with crinkled paint. They used a big street sweeper-wet scrubber to clean the floors in the factory of oil and grease spills from forklifts, tugs, etc. The sweeper operator was mixing in some "Hot " solvent, to better remove the grease and when he ran past the Paint ovens the solvent fumes were being drawn into the fresh air intakes for the paint booths.
05-09-2013 09:26 PM
ggorman Thanks. I'm not talking about a large area so tomorrow I'll sand the base and the sealer and start over with a new seal coat. The substrate was well sanded with 400 and clean before the sealer went on. I didn't spray the seal coat evenly since I figured it would hide anyway. So I don't know if it was too thin or too thick. Live and learn, I'm only 72 so I have time to do it right.
05-09-2013 09:17 PM
MARTINSR It likely happened because the sealer was too thin, so the solvents from the chromabase went thru it, lifting it off the substrate. Or it was too thick, and didn't fully flash off so it was soft and the same thing happened, solvents from the chromabase went thru it.

The other option is that the substrate wasn't sanded properly and the sealer wasn't adhered to it so the solvent from the chromabase went under it.

05-09-2013 07:35 PM
crinkle spots in base coat

This afternoon I shot DuPont ChromaBase over Nason urethane sealer and had a couple of spots react like it wasn't cured even though I waited quite a while. I didn't time myself but I went to lunch.

Is there any reason to ChromaBase would react to the Nason product?

Now, can I sand these spots to flat and recoat?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 11:17 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.