Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> narrowing a rear end?
User Name
Password
lost password?   |   register now

Thread: narrowing a rear end? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-25-2013 04:07 PM
big gear head Some rear ends are easier to narrow than others. Most c clip axles can not be resplined. The 9 inch Ford, Dana 60 and 8 3/4 Mopar axles can usually be resplined. I would be careful about using resplined axles. They are not as strong as axles that are made to the correct length. If you break an axle on that trike you are going to be in for a wild ride that you might not survive.

You do need a housing fixture to align the housing ends with the differential bearing bore. If you don't get this straight you can have all kinds of problems.
05-25-2013 03:28 PM
BOBCRMAN@aol.com If you have the equipment to do it.

Narrowing a housing, you need to have some way to get it straight. I make a fixture from bar stock. With donut spacers cut to fit the center carrier bearing saddles. Also the outer bearing housing. A steel plate to clamp to each end of housing. Then the housing is cut to dimension. Spacers installed and bar inserted. Tack weld prepped housing in three places, each end. Bar should turn easily. Then weld housing.

Axles are a different matter. If the axle isn't tapered too much from flange to spline and there is enuff diameter to spline. It can be cut and re-splined.
I used to do these in house. But the PIA factor and the toughness of most axles. I send them out to Moser in Indiana. Moser Engineering - Moser Engineering - Home
05-25-2013 12:00 PM
HemmiGremmie
narrowing a rear end?

Hey everyone.
Been chattin about my v8 trike and it seems that due to power vs weight i may not want a posi unit.

If not im lookin at maybe a older 6 lug open carrier ford rear with 3.55 or 3.23 gears.

My question is this...
how hard or expensive would it be to take an old rearend and narrow it? Do i need all new axles or can they be cut n repslined? Expensive????

Just need the basic details. Tnx...hg

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.