Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Assembly Lube's, 4Jaw Chuck- I need your recipe!
User Name
lost password?   |   register now

Thread: Assembly Lube's, 4Jaw Chuck- I need your recipe! Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-14-2002 10:53 AM
Mrfixmaster I've been using White Lube on all my engine re-bilds for YEARS, and haven't had any problems. I agree with 4-jaw on the cams. Don't vary from manufacturers specs on those.

08-14-2002 09:04 AM I would be wary of the vaseline since although it is a petroleum grease, it isn't designed as a high duty lubricant. Hydrodynamic bearings that are all over an internal combustion engine and worst of all, camshaft lobe/lifter interface, all depend on a couple of molecules of lubricant to prevent metal to metal contact. If those molecules aren't specifically suited to the 2,000psi it will see in main and rod bearings (even higher in camshaft lobes), the pressures will collapse the lubrication film and bye bye bearings.
08-14-2002 08:42 AM
bullheimer in case anybodies wondering, i was told i could use vaseline back in the 70's, i think it was my 392, and i did, and it worked fine on the main and rod bearings. it is petrolium after all.
08-11-2002 08:44 AM
4 Jaw Chuck Nah! I just keep adding moly until it is a sticky mess. It's a good idea to wear rubber gloves when you do it, moly powder is impossible to get out of the pores of your skin. Those cam lubes are more of a paste so keep adding moly until you get a paste.
08-10-2002 12:20 PM
americanfreedoms 4Jaw,

Do you have a recipe?

08-10-2002 09:49 AM
4 Jaw Chuck I mix it with synthetic grease, the only difference between the "cam" grease and the moly bearing grease is the amount of moly in the mix. Being able to mix it with synthetic is a plus.
08-10-2002 04:25 AM
americanfreedoms 4JawChuck, I have a supply of Moly powder. How do you make your own?

08-10-2002 02:58 AM
4 Jaw Chuck I use STP for all engine assembly except for rings, straight 30wt for that. If you buy some moly powder you can make your own lube. Lubriplate is OK too but not for cams, I don't take chances with cams.
08-10-2002 02:48 AM
Assembly Lube's, 4Jaw Chuck- I need your recipe!

I was hopeing to get the boards opinion on assembly lubes.
I see where my cam came with a small tube of moly grease, so that is what I plan on using on it.
But for the rest of the engine what do you guys recommend?
I have a rather large container of LubriPlate grease (kinda cream color), would that make a suitable assembly lube?

Thanks again,


[ August 10, 2002: Message edited by: americanfreedoms ]</p>

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:29 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.