Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> 53 Belair conv rust repair
User Name
Password
lost password?   |   register now

Thread: 53 Belair conv rust repair Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
Today 09:27 PM
John long
Quote:
Originally Posted by deadbodyman View Post
theres a lot to be said about a removable tranny tunnel too ...
That is a good thought. Now would be the time to do it but I was kind of afraid I would end up putting the seam right where the shifter went.

Maybe I should rethink this a bit.

John
Today 09:21 PM
John long
Quote:
Originally Posted by Too Many Projects View Post
Do you know what transmission you will have yet ? You might want to hold off on the tunnel to measure for clearance of a different trans. If it is the 4 speed, you should have room. A 5-6 speed or 4l80 may need a taller floor.
I agree. I have had a good Muncie with a new shifter sitting on the shelf for several years looking for a home. My intent is to put it in here. I also have a good Saganaw that I might put in it if I decide the car is for sale. I would hate to see my Muncie go down the road.

John
Today 09:20 PM
deadbodyman theres a lot to be said about a removable tranny tunnel too ...
Today 09:16 PM
Too Many Projects Do you know what transmission you will have yet ? You might want to hold off on the tunnel to measure for clearance of a different trans. If it is the 4 speed, you should have room. A 5-6 speed or 4l80 may need a taller floor.
Today 08:17 PM
John long The front pans are fitted and I have the transmission hump template ruffed in. it appears this section is going to be very straight forward.

John



Yesterday 07:56 AM
MARTINSR Great tip John, thanks!

Brian
Yesterday 07:00 AM
John long
Quote:
Originally Posted by Too Many Projects View Post
That IS a slick trick for plotting panels...

Car is looking great. It should be far enough along to attend shows next year as "in progress"....
Thanks Mitch. You would be right if it was on a usable frame but alas, I still have to pull the frame out from the hardtop and build it.

Not sure how the finances will play into this either. Time will tell.

John
Yesterday 06:48 AM
Too Many Projects That IS a slick trick for plotting panels...

Car is looking great. It should be far enough along to attend shows next year as "in progress"....
09-15-2014 09:56 PM
496CHEVY3100 A very good tip John ,thanks for the information It will be useful in the future,
09-15-2014 06:32 PM
John long I would like to share another little trick that I started using making upholstery panels. The neat thing is it works just as well for any other pattern.

Michael's Craft store, some Walmart's and other fabric stores sell a heavy clear plastic material that is 3-4'mills thick. It reminds me of plastic convertible top window material and the last I purchased was 3.95 per linear yard on sale at Michael's.



Take a piece of material and lay it on the panel You need to make a pattern of and either choose or create a reference line. Here I used the lip of the toe board.

Since it is clear you can see everything you want to copy. If it was a door panel you could mark the window cranks, door panel clip holes, arm rest holes, etc. For a bigger piece spray the clear material lightly with spray adhesive. It will hold it in place but will still be easily removed and laid on the material you are marking and will stick again there. Also, since only the material is sprayed lightly the panel will remain glue free. A Sharpie is perfect for marking it.

I did not need for it to be stuck since it was a small pattern and not very complicated. Tape worked well.

Look closely and you can see the material taped on this part of the floorboard and the bolts and floor board sections marked.



Now the clear pattern is laid on the floorboard and the lines are transferred to it as well as the location of the body mount bolt.



I trimmed the panel with my plasma cutter next. I admit, I played it safe and cut it slightly undersize first and then did a final trim cut.





After a significant amount of tweaking the panel and my floorboard supports it lays in place nicely and is about ready to be drilled and plug welded in place.

Hope this helps some one that needs a simple fail safe way to make patterns that do not lend them selves to simple measurements.

John




09-13-2014 08:15 AM
boothboy John, it just looks great. Thank you for all your posts!

BB
09-13-2014 08:12 AM
MARTINSR
Quote:
Originally Posted by John long View Post
It really did do a good job and I used less media than would fill a gallon jug. Pretty cool.

Just finished cleaning the gun. Now I won't have to watch my floors turning brown. At least not the top side.



WHOOO HOOOOOO!!!!!

Brian
09-13-2014 03:12 AM
123pugsy Real cool John.

It's always a great milestone to hit the primer stage.
09-12-2014 09:45 PM
NEW INTERIORS Look's great !!!!! What a great build to follow along...Thanks for sharing...
09-12-2014 09:39 PM
cruzinTLT
Quote:
Originally Posted by John long View Post
It really did do a good job and I used less media than would fill a gallon jug. Pretty cool.

Just finished cleaning the gun. Now I won't have to watch my floors turning brown. At least not the top side.



A thing of beauty! Congrats on getting to this stage in your project--I have been amazed at the great job you are doing!
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:39 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.