Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Two wheeled hot rod art.
User Name
Password
lost password?   |   register now

Thread: Two wheeled hot rod art. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-15-2003 06:06 PM
daimon1054 I have seen the flush light's that are painted and only show up when on but I think this will look killer.
11-15-2003 03:15 PM
Halloweenking The fender is a longer tailed version of a west coast chopper classic fender. Not much difference though.

The horse was first drawn out with a sharpie then after 6 or 7 tries untill it was right, drilled a few starter holes in each section and hand ground it out with some small bits and an air powerd pencil grinder. Afterwards cleaned up with some hand files and very thin peices of sandpaper or cordpaper. No plasma cutter could cut that out that small, if it could I would have been all about it. It wasn't stamped out of a flat sheet, it was carved from the formed peice. Not very hard at all anyone can do it. It measures roughly 8" tall X 5-7" wide from nose to tail. Never really measured it.It should look superb with black paint and a retna burning red LED.

Kevin, our quality control manager at work thought the same thing, lazer cut untill she took a walk to my little playroom and saw the aftermath.

If you try this wear gloves!

Back to paint.

HK
11-15-2003 02:58 PM
daimon1054 That does look sweet, I would guess that it was stamped out flat then the fender formed but again just my guess.
11-15-2003 01:37 PM
BigBlockBabe That's soooooo cool. Good job HK!
11-15-2003 06:22 AM
M&M CUSTOM Looks like the result of a steady hand and a plasma cutter to me.
I haven't used my cutter for decorative purposes as of yet, but I am certain it falls within the capability of the machine I have.
Nice work HK.
11-15-2003 04:58 AM
horvath Dremel???

Alan
54 Chevy Pickup
11-15-2003 04:23 AM
Kevin45 HK..how'd ya put the horse in? Laser cut? Looks good.

Kevin
11-14-2003 10:49 PM
milo way cool
11-14-2003 10:04 PM
horvath Way to go, bro'! Typical top-shelf work! Ain't nobody like the Halloween King!


Alan
54 Chevy Pickup
11-14-2003 09:10 PM
johnnymopar pretty nasty!

JB
11-14-2003 08:50 PM
tm454 Nice looking tail dragger King!! Should make a sweet scoot. Keep the pictures coming, can't wait to see it finished man!


Todd


Rat Rods Rule!
11-14-2003 06:31 PM
4 Jaw Chick Very nice HK!! The detail is fantastic.

Chickie.
11-14-2003 06:12 PM
Halloweenking
Two wheeled hot rod art.

This is my bro's bike I've been working on for the past few weeks/months. There are only a few shots here of the actual art and subject of the post.

The rear fender took aproximetely 15-20 hours of work to complete. A custom light enclosure had to be built (not installed). Simple modification do to the ease of installation with the new "plug in" style LED's. Just a simple light box made of 20ga sheet-metal with your old light socket tacked to the inside after removal of original housing. You can have the box chromed or polished (aluminum(larger gage of course)) for better light reflectivity or you could just mount a small peice of mirrord plexi or lexan around it, or with LED's white paint works just as well.

The paint will be HOK polyurethane jet black with a poly clear. Everything else on the bike has been black powdercoated and unrelated to th topic, is either new or rebuilt. Open belt drive, S&S heads ect ect. Paint should be done by the morrow, will try to get more pic's if I can score the use of a digicam for another favor.

HK





Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.