Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> No backing plates
User Name
Password
lost password?   |   register now

Thread: No backing plates Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-02-2004 01:53 PM
darom Similar question. I have a 67 Camaro and was considering this kit since it utilizes the stock drum spindle.
http://www.ecihotrodbrakes.com/disc-...ec-723ack.html

Can I just buy stock GM backing plates from Napa or any other store or I would have clearance problems?

Thanks for your help!
Denis
'67 Camaro RS

PS Also, would my brand new drum brake lines (rubber) adapt to this kit? Do the disc brake lines use different NPT diameter?
01-02-2004 12:07 AM
jimfulco They do have a small protective flange around the inner bearing seal area. Don't know just how important it is though.
01-01-2004 05:27 PM
rakundig Thanks for the info.

Can close this thread now moderator...

Rick
12-31-2003 09:39 AM
scholman Rakundig,

These plates also catch a little more air for cooling. They are bent out just a bit, like a scoop, so air will blow over the rotors. If you have solid steel wheels like the originals which were for drum brakes or wheels like the old centerline's that do not have any openings through them, I would install the plates so you don't over heat the front pads and end up with "brake fade".

Scholman
12-31-2003 08:00 AM
poncho62 They are put there to keep water and mud etc off the rotors. The other side is protected by the wheel. I don't have any on my truck and Ive been all over the country with it in all weather, except snow. I dont think they are necessary , especially on a fair weather car.
12-31-2003 07:46 AM
tm454
disc brake backing plate

The one side never has a plate and the other side does. I have a Mustang II disc setup on my 37 Dodge, it didn't come with any backing plates and I don't expect any trouble, after all what could be the difference now that both sides don't have a plate?? If I had them I would put them on but I don't have them so I won't.


Tazz
trolloligest


Rat Rods Rule!
12-31-2003 12:25 AM
rakundig
No backing plates

I have a disc conversion kit for my front end of my 68 Camaro but it didn't come with any backing plates. How big of a deal is this? I have found a place that will sell me plates only for that kit and I am wondering if this is something I can put off or if it is a show stopper?

Thanks
rick

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.