Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> needing some help please
User Name
lost password?   |   register now

Thread: needing some help please Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-29-2004 08:12 PM
lluciano77 I have done that swap. I have a 5.0 (that is the H.O.) in my '61 Ranchero.

You need a 50 oz flywheel and balancer.

The oil pan must match the timing cover, ( the early pans had the dipstick in the timing cover, in the later years it goes through the block). Also, your oil pump pickup must match the oil pan you will use. Watch out for the late model timing cover that doesn't have a fuel pump boss, unless you will be using an electric pump.

Make sure you have valvesprings that will handle the roller cam.

It is going to be a tight squeeze getting the engine in and out of the car. I highly recommend taking the engine/tranny combo out in one piece.

You may have to take out the standard transmission pilot bearing in the back of the crankshaft.

I used Hedman headers from a Maverick. It is very tight, but the 1 5/8" ones will fit. They are pretty cheap too.

I also used an 8" rear from a Maverick. It is 1/2" narrower on either side. It will help make room for bigger wheels.
01-29-2004 07:59 PM
Aberium I would ask my Dad but he past away about 6 months ago that's why it is important for me to change it back the way he liked it. I would hire someone but I feel this would be disrespectful to my father. I know he would want me to do it myself and get some wrench time in.
01-29-2004 07:39 PM
KULTULZ I am assuming that what you have in there now is an early 302? And you want to upgrade to a later 5.0L (carb or FI)?

It should slip right in. There were no major changes between the years. The only problem that you might run across is there being no mounting hole for the clutch bar on the later 5.0 but there is a kit to remedy that.

If this didn't help or answer your question, hit me up again...
01-29-2004 06:12 PM
Centerline I'm not a Ford guy but I believe the differences between a 302 and an 302 HO are 99% internal. If I'm wrong I'm sure one of the Ford guys will straighten me out but as far as I know the HO engine should be a bolt in replacement with literally no modifications whatsoever.

01-29-2004 01:15 PM
302 swap

There are many Ford guys here who might lend the benifit of their experience since you asked so nicely. Just curious, why don't you get your Dad to walk you through this?


Rat Rods Rule!
01-29-2004 11:48 AM
needing some help please - engine swap

I was wondering if anyone knew where I could get some info on changing a motor. I have a 64 Ford Falcon that has a 302 in it right now. My Dad use to have a 302 HO in it though I was wondering If anyone knew of a breakdown in the steps to change these motors. Like I said the HO was in there before dad put the 69 model 302 in it so I was thinking it should change out pretty easy I just don't have a lot of wrench expierence. So if anyone knows of a site or any info about the steps to change these out I would really be thankful. Thank You

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 12:33 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.