Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> power steering from long water pump to short water pump
User Name
Password
lost password?   |   register now

Thread: power steering from long water pump to short water pump Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-22-2004 07:22 PM
302 Z28 Listen to Bob, drilling accessory holes in early heads never works. Don't let anybody mess those heads up by telling you outherwise. There is not enough material there.

Vince
02-22-2004 06:56 PM
BOBCRMAN@aol.com Drilling and tapping the heads for acc. holes does not usually work. There is not enuff meat in the front of the heads and the outer surface is not flat. I've seen it tried many times and it usually always is at best a cobble job.
To address the hardened seat problem, check out the prices before you just drop the heads off. I've been in this business for over thirty years and by the time you pay for the seats and all the other things involved(guides, valvejob, mill, seals, etc) you can buy a 350 complete engine (or even a car) and have all the brackets you need plus a better engine for your purpose.
02-22-2004 06:30 PM
kellyem Thanks for the responses. I have zero brackets and the only pulley I have is on my power steering pump. I don't have a water pump neither. I was planing on buying new brackets and pulleys. I have not had the heads to the machine shop yet, so I'm going to get the harden seats. While I have them there, should I have them drill and tap some accessory holes? Do the holes pose any problems like leaks?
02-22-2004 08:56 AM
troy-curt You have several options.

Buy or make all mew brackets so your accessories stay in the original place, or use the brackets that go with the engine, 68 and earlier, and re plumb and rewire everything. Just be sure the fan sets in the shroud where it should. Good Luck.

Troy

__________________
If you don't make mistakes. your not doing anything.

69 ss rs full custom camaro 98 ISCA grandchampion
69 ss rs bb camaro wifes driver
66 Elcamino 350/all dz parts,ac,windows,loaded,my driver
69 ss chevelle bb conv.fresh frame off
26 T sedan street rod
02-22-2004 08:34 AM
302 Z28 There is a bunch of options you can go to. Your best bet IMO is to got to someone like Vintage Air, or HotRod Air. Zoops also makes an excellent line of quality brackets. Most of the brackets have been developed for street rods which almost always use the short chevy water pump due to clearance issues. So just about all their brackets are for short pumps. Vintage and Hot Rod Air both have brackest that bolt only to the water pump and intake manifold. Theses are for the early heads, or a situation where you wish to keep the accessories in close to the engine.

Vince
02-22-2004 07:53 AM
BOBCRMAN@aol.com No your pump will not work, neither will the other pulleys. You have encountered the biggest downfall associated with using pre 70's heads. You can fabricate a bracket of sorts that uses the front intake manifold bolt and the front exhaust bolt on the alternator side. I have never seen one commercially available but I've made them from 1/4" stock, a lot of labor and some torch work. DO those heads have hard exhaust seats? If not you will also have durability problems.
02-22-2004 07:51 AM
poncho62 Both your PS and alternator would be on the same side. I'm not sure if they would interfere with each other.
You don't necessarily need the accessory hole to mount the alternator. You can make a bracket from angle iron extending from the front exhaust /header bolt.
02-22-2004 07:38 AM
kellyem
power steering from long water pump to short water pump

I have a '79 Monte that I'm putting a 283 into. Here's my question. I want to keep my power steering, can I use a short water pump and still keep my power steering pump? The reason I want to go with the short water pump is because the heads do not the assy holes in it. It seems there are more options for using a short water pump over the long. I think I've heard if I use a triple groove crank pulley I can still use my power steering pump. Does anyone know if that's true?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.