Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 302 roller buildup suggestions?
User Name
Password
lost password?   |   register now

Thread: 302 roller buildup suggestions? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-10-2004 08:26 PM
red347 I also went with the Victor Jr's on my 347 stroker. Bought them bare, installed Ferrea's with 5 angle cut. Also ran a Victor Jr. inatke with the same combo. Have since done some other mods, but the Vic's were excellent. I have now gone well beyond streetable, but satill have the Vic. Jr's and a new Super Victor intake. If you plan a 100K miles, I would go for the 331 instead.
Check out www.jdsperformance.com for the stroker kit

Ron
03-10-2004 07:28 PM
Carbed95GT I think it pretty much depends on what kind of performance you're going after. I've had a 347 in my '95 since 2001. I started off by using GT40 irons, an E303 cam (which was a bit on the small side for that stroker), Cobra intake, headers, off road h-pipe and side exhaust. I was real happy with the performance as a mild street car, but I wanted something more. I ended up ditching the EFI all together, grabbing a set of Vic Jr heads, and a TFS stage 3 cam. Still very streetable, but not "mild" by any means. Holley makes a good cylinder head and all, but for all out performance, I'd probably opt for the Vic Jrs or a set of AFR heads. Just my $.02.
03-07-2004 10:13 PM
billybob_v10 Thanks for the help. It seems no one replies to anyone's Q's anymore. Thanks again for the help. Billybob
03-03-2004 12:08 AM
lluciano77 I would guess that you would get another 40 hp more with the 347 kit and the Holley package.

The Holley kit will work with a 347 stroker kit.

There are a lot better heads out there that will make more power than the Holley heads. Look in Summit magazine. They have a Trick Flow package similar to the Holley one. It will make way more power.

Or, you could buy some AFR heads and pick your own intake and cam combo to go with them. This might be the way that you can make the most power and still be street able.
03-02-2004 09:51 PM
billybob_v10
302 roller buildup suggestions?

I just aquired a 1988 302 HO long block from an 88 mustang for $50. I am boring .030 over and would like to put on the Holley SyteMAX II Kit from summit. The kit inludes new Holley heads, new intake, timing and cam. The ad states that with the kit, the 302 will push about 350hp. Can I use that kit in conjunction with the 347 stroker kit? Will I need to change cams because of the stroker kit? How much hp will the two push together if they work? Will the new intake from the Holley kit flow the proper amount of air required? Thanks for your help. Billybob

Or would it be better to just rebuild it with the Holley kit and not do the stroker? If I use the two in conjuction, what intake will perform the best and flow the amount of air needed to fuel the beast? Thank you, billybob

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.