Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Lakewood Clutch fork clip broke/angle of clutch fork
User Name
Password
lost password?   |   register now

Thread: Lakewood Clutch fork clip broke/angle of clutch fork Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-23-2004 08:04 PM
ratlover Emailed sheets hope it helps. here's the clutchball setup for anyone else who cares. I might have screwed up the description of the procedure a little, but check it out if you need to know.
04-21-2004 11:58 PM
70bird ratlover

I would appreciate you emailing me those installation instructions. my email is cliff@bak.rr.com

I did not build the car a friend did and then it just set in his garage for a year and a half. He put 1450 miles on it. Now I'm putting miles on it and finding the flaws.
04-21-2004 10:52 PM
ratlover I have never heard of this happening, but that does not mean it is impossible. My guess would be that your clutch fork pivot ball definitely needs to be setup. If the geometry is off then in order to get sufficient clutch disengagement, the fork would kinda be on it the "tips of it's toes" trying to reach far enough and the bearing flange could returnsliding between the spring and fork. I have the identical setup (454,dual friction,lakewood,T-10) have not had that problem yet. I have the installation instructions if you need them can email if required. I measured by calculating the position off of the bellhousing face, based on the measurement they spec. They measure off the flywheel face. With a dial gauge I measured the distance of the face from the back of the engine with the flywheel on the crank. add the thickness of the engine saver plate, and then add the distance from flywheel face to the engine (bellhousing mating surface) to the spec they give you. then you should be able to measure off of the bellhousing flange to the clutch fork ball like in the pic I am attaching.
04-20-2004 03:15 PM
70bird
Lakewood Clutch fork clip broke/angle of clutch fork

I have a 502 in my '70 firebird, a lakewood bellhousing, centerforce dual friction clutch, richmond T10 tranny, and a ford 9" rear end with 3.70 limited slip. The lakewood clutch fork is held on by a spring clip to a pivot ball. I was slowly accelerating from a stop sign (my 2 year old was asleep in the back seat) when "clack, clack, clack, clack,......" started comming from the bellhousing area. I pushed in the clutch and it stopped. It only happened when the clutch was engaged. Luckily I was 2 blocks from where I was going. I pulled the whole thing apart (engine tranny removal) knowing it had to be related to the clutch. The only abnormality (besides the worn distributor gear) was that one of the prongs on the spring clip that holds the clutch fork on had broken off. It also apprared that the throw out bearing had been riding half under and half over it's retaning clip. Is it possible that the throw out bearing popped itself off and back on improperly and if so, what can cause that to happen? Improper clutch fork alignment/angle? Too much travel of the throwout bearing when the clutch is disengaged?

I guess I just need to know how to properly align or adjust the clutch fork and amount of throw. There is an adjustable pivit ball on the bellhousing. Any help would be greatly appreciated.

70bird

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.