Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Is it possible to tell spline count from axle tag?
User Name
lost password?   |   register now

Thread: Is it possible to tell spline count from axle tag? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-13-2004 05:35 PM
Dubz What size of a press would be required for installing the bearings

edit: some day i'll learn how to spell or hit the spell check button before posting
10-13-2004 03:38 PM
Dubz mounting surface diameter is only 8" on this one though, the teeth protrude wider, still it's the right thing

well that is nifty

thanks a bunch
10-13-2004 02:23 PM
RG markings

FoMoCo logo U.S.A WAC-4210-A |> 8 5 88 Shift #3 B6

PG marking

FoMoCo logo WAS 4610 A |> MX 1 USA

RG has 32 teeth
PG has 9 teeth
Relax, you're OK...

The stampings I.D. the gear set as B7A 4209-D, which was origionally a 3.56. It was replaced by B7AZ 4209-L (35/10) and later C9OZ 4209-A (35/10) and they were both 3.50's.

Some of the first RG were not 9" but 8.75" in dia. They progressed to 9" as time went on.

-MEL Engine Forum-
10-13-2004 12:44 PM
Dubz RG markings

FoMoCo logo U.S.A WAC-4210-A |> 8 5 88 Shift #3 B6

PG marking

FoMoCo logo WAS 4610 A |> MX 1 USA

RG has 32 teeth
PG has 9 teeth

i think i maybe got hosed as if they use the same kind of code as the axle tag i have a 5.88 gear from a 8"

looks like i did get screwed, ring gear measures 8" outside diameter, inner diam 5". Pinion gear measures 4.5" across. The 3.56 gear wasn't common, so i'm not having any luck looking up info on it, if there even was such a set

ok, found this site that lists FMM-4209-A356
which is a FORD 9 3.56 RATIO O.E.M STYLE FORD
for $556.50

so i'm guessing it was a rarity.

please oh please help me, i'm either happy i have something rare, or ticked that i have something that won't work
10-12-2004 11:25 PM
bud-23 Hey KLUTULZ. I have a Lincoln Versalis sp? and when I changed gears I found out there were 3 different bearing sizes. 130 mile round trip to get the right ones.

10-12-2004 11:14 PM
Dubz I'll have to go dig it out and get you the casting info from them, i know they have numbers as well as the FoMoCo logo, i wrote them down a while ago but lost the paper.
10-12-2004 05:36 PM
KULTULZ 28 Spline Count

Carrier Brg Cone I.D. 1 25/32" CUP O.D. 2 57/64"

Wheel Brg Tappered Roller I.D. 1 9/16" O.D. 3 9/64"

Do you see any I.D. markings on the RG/Pinion?
10-12-2004 02:21 PM
Is it possible to tell spline count from axle tag?

Just wondering if i need to actually pull the axles and count, or if i could decode from my tag. Rear is a 9". Also was wondering about bearing sizes, if there was any way to tell those without disassembly.

Axle was under a 74 Gran Torino

axle tag reads as such as far as i can tell

2 75 9 844B

so i know it's an open carrier with a 2.75 ratio, that the ring gear is actually 9" that it was assembled on a monday of July in 74 (4GA)

Also i got a used gear set for my rear i was planning on swapping out (why i would like to know bearing sizes ect) and it's ring gear is quite a bit smaller than 9". it's an original FoMoCo gear set that i got used in great condition, it's 3.56 which i've heard is supposed to be uncommon, anything i should know about the smaller ring gear? or should i get a set of newer gears in a diff ratio that will actually have a 9" ring gear

Thanks for the help

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:41 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.