Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 55 chevy, 265 rear main seal
User Name
Password
lost password?   |   register now

Thread: 55 chevy, 265 rear main seal Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-19-2004 09:27 AM
killerformula is it possible to order a one-piece adaptor? I know they exist....

k
10-19-2004 06:59 AM
k-star
yep

Thats the one i used. I installed it in the last 57 283 i rebuilt. No runs, drips or errors....... I did not buy from them but i am sure it's the same seal.....

Keith
10-19-2004 06:48 AM
slingslingbinks i found this and i wonder if it would work http://www.danchuck.com/05_04_rear_main_seal.html
10-19-2004 04:56 AM
k-star
seal

I have never seen anybody put a rope seal in with the crank still in place and not have it leak!!!!

But there is good news there is a replacement that is a lip seal design like a standard small block.

The bad news is i just can not remember for the life of me where i got them???? I still have one left and if you cannot find one i'll sell it to you if you need it. I'll try and look to see if i can find where i bought it from.....

Keith
10-19-2004 01:52 AM
11echo slingslingbinks, well I'm sorry to tell you but I've never seen a replacement seal for the rope one. I've built a few Pontiacs in my time, 326, 389, & 421 ...they all used the rope seal. Actually it's not a bad sealing method either! Afew tricks to use, be sure the rope channels are clean! Take a coal chisel and but some "dings" in the channel (this helps from spinning the seal). Try to get a solid piece of wood or pipe about the same diameter as the crank journal and use a rubber mallet to "seat" the rope in the channel. Use a razor to cut the rope ends flush & clean, then use some silicon sealer on the rope ends.
It's not a hard job if done correctly, and will last as long as any factory seal ...in my experience. Just don't complicate the issue by trying to do this with the car jacked up, pan off, and just the rear bearing block off. ...And maybe flat on your back!!? ...It may be a "pain" to pull the engine, but remember the old adage ..."Never enough time to do it right, but aways enough time to do it over!" Truer words were never spoken! ...Again, in my experience, Good Luck to you Sir. ...Mark
10-18-2004 08:29 PM
slingslingbinks
55 chevy, 265 rear main seal

I'm trying to replace a rear main seal on a 1955, 265 small block chevy. The orgional seal is a roap type. Does anyone know of a 2 piece lip seal that will fit the block and main cap. The engine is in the car and the replacement roap seal installation into the block bite's. The seal won't pull into place with the installer and it keeps pealing it back even with the main's loosened up and the crank droped down. Some one must make a 2 piece lip seal that will fir this app. Does anyone have any ideas for me other than pulling the engine and crank and installing the roap seal per the repair manual. tks' sling

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.