Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Cylinder heads
User Name
Password
lost password?   |   register now

Thread: Cylinder heads Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-06-2003 06:54 AM
nickel333 Get some aftermarket heads, sportsman 2,iron eagle, pro action,the deck surface is thicker for Blowers and nitrous and stuff,Youll have more power out of the box than you could get with your ported stockers, and if your buying a blower whats another 500 bucks for some good bare heads ya know, you already have to buy valves and springs, and im guessing you have rocker studs and guide plates. If your going to the extent of the blower then why leave yourself short handed on the heads. Hell you could probably sell your stockers for a 200 bucks to some local kid that needs a set of heads. good luck and have fun
02-06-2003 06:24 AM
SLOW BILL T Man I had really good luck using stock castings on a 355. you need to take a few precautions though. Make sure the guides are in perfect shape, especially the intake guides. Also I had very good luck using a full face 45 degree angle lapped in on the exhaust valves to get heat away from the valve. valve seat pressure is also critical. we ran this 355 @ 40%over on alcohol in a small tractor & had very good luck. hope this helps.
02-06-2003 12:04 AM
78 monte I guy I know at the track has,unless I seen wrong stock large chamber heads on his 10.0sec drag car with a blower.
02-05-2003 08:26 PM
T man
Cylinder heads

Ok, it seems pretty obvious that I should look for another block for my motor project. Now I'm
wondering about the cylinder heads. I've heard that stock heads tend to crack between the valve seats. I have a set of heads that came off a 69
S.S. Camero that have been ported and polished,
machined for scerw in studs and guide plates.
But I still need to get the valves and springs.
A friend of mine says that I'd probably be a lot better off going with a set of World Products heads, tham using the reworked stockers. The heads are going on a blown motor, and I don't want to have be worrying about heads cracking.
Has anyone had any luck with reworked stockers on a blown small block?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.