Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> 96 Chevy p/w won't start, help please
User Name
lost password?   |   register now

Thread: 96 Chevy p/w won't start, help please Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-29-2004 10:06 PM
sbchevfreak Just so I'm sure, TBI, not VORTEC, right?

Another thing to check is the pickup in the distributor. I had one come into the shop, similar problem, and the pickup was totally fubar, but you couldn't tell unless you pulled the rotor off.
11-28-2004 09:19 PM
No start

If you find a blown fuse check the wiring harness at the injectors and make sure they have no exposed wiring that the air cleaner might be blowing when it is put on.
If you find no blown fuses, If you look by the fuel pump relay you will find a single red wire with a black connector. That is a test lead. If you apply 12v to it the pump will run. If it runs then the wiring to the pump is okay. But this vehicle since it was running before I just don't see any Relay of PCM problems.
If you have fuel under pressure, spark, injector signal, then you may have a problem with injectors stopped up. When you pulled the tank was it good & clean inside? Fuel look good, no signs of water or anything else?
Very seldom have I had to replace injectors unless they were contaminated from bad fuel (excessive water or someone dumping other chemicals in the tank). You might want to take a fuel sample in a clean glass jar and let it sit for a while to see if it has anything in it.
When they tested your pump did they do it with a fuel gauge? Had it completley quit running or just running poorly? Pull a plug and see if it's burning clean or it appears to been burning something else.
11-28-2004 08:33 PM
96 Chevy won't start

I installed a new filter, however, I will check the injector fuses. It is a TBI and I have not idiot lights. It was dying at stops lights and won't run with A/C on. I pulled down the tank again to make sure I installed the new pump correctly. I wondered if I tripped something.

11-28-2004 08:21 PM
No start

Is the fuel under pressure to the intake? Maybe a restricted fuel filter instead of a pump out? Check all fuses-- inj1, inj2.
When you turn the key on do you hear the pump run for a few seconds? If not check fuel pump relay. If it runs while pouring fuel in the throttle body I do not think you have a PCM problem, or module trigger problem from the distributor, however it is not impossible to loose a PCM injector drive circuit.
Is this a Throttle Body unit or a Muiti-port unit? Any Service engine soon light?
11-28-2004 07:44 PM
96 Chevy p/w won't start, help please

I know this is my first post, however I really need some help. I have a 1996 Chevy C1500. It was running poorly, I took it to a local mechanic for diagnostics. I was told it needed a fuel pump. I was quoted $350.00. I decided to fix it myself, I dropped the tank, changed the pump, added a new screen. I replaced the tank and guess what? No start. I have gas, spark and if I shoot some starter stuff in the TBI is will start and then die once it burns off the starter fluid. What did I miss? I took off the lines from the back of the throttle body and I have gas. Is there something I missed?

If some one has some suggestions, it would be helpful.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 03:49 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.