Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> distributor timing problem? help
User Name
Password
lost password?   |   register now

Thread: distributor timing problem? help Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-04-2005 06:29 PM
redneckrodder hey...i beleive it is the carb, it was backfiring(or afterfire lol) from the carb and exhaust, the timing is very good, had 3 other techs, including myself double check it. the carb was sitting for a good 5-6 months and was also used prior , it was just sitting on a shop floor...what do you guys think? im going to swap it with my buddies holley and see if it goes away then i'll now if thats the problem, but i was just wondering if that seems likely?
01-03-2005 10:52 PM
hosep just having a little fun. no offence
01-03-2005 10:51 PM
underdog305 yeah yeah.. Does make sence though, doesn't it? laughing...
01-03-2005 10:45 PM
hosep I knew I would wind some one up!!!
01-03-2005 10:15 PM
underdog305
Quote:
By the way any fire is a back fire. I never heard that other one. I go with miss fire, but the other sounds like politically correct bull.
Hosep,
That was the term I was taught when I went to school for Aircraft Maintenence 15 years ago. I'm about as far from politically correct as they come. It's a way of being specific about the direction of the fire. Direction is absolutely critical when troubleshooting a problem like this. Terminology is an important tool for diagnosis, otherwise nobodys on the same page.
01-03-2005 09:58 PM
hosep Ok , here we go I had this same problem for years working on first gen SBC. I came across this somewhere and it worked. the more radical the cam the less margin you have to work with. I have done these SBC for 41 years. here it is. follow it to the letter and it will work. I did not write this only copied it.

Setting Valve lash
Centered on the base circle EO/IC
Exhaust opening/intake closing
When the exhaust valve just starts to open, stop cranking and adjust the lash on that cylinders intake valve.Crank the engine again watching the intake valve of the same cylinder. After it is fully open and the rocker tip is at the bottom of its travel crank slowly until the valve is 2/3 closed. Stop and adjust the exhaust valve on that cylinder. repeat on each cylinder.

With hydralic lifters I give them 1/3 to 1/2 turn from "0". not the factory spec of 1 full turn for lash.

This may be time consuming but it works. I remove the spark plugs when doing it to stop crank back from compression. I also use a remote cranking switch, ignition off .I then set the distributor to #1 at TDC checking the timing marks on the balancer. Then fire it up. Set the timing with the light, vac advance plugged. Check the weights in the disrributor for binding first. Sorry forgot that one. time it 6 to 8 degrees. Warm it up and run it at slow speed to purge any air from the lifters.
Now after all that put all the tools away but the wrench for the distributor. drive the car. hammer it, slow take off , do it all. and listen and use the seat of your pants to fine tune the timing. when you get it just right you will know. Just do very small moves on the distributor.
I think you have an exhaust valve hanging open. It is easy to do.
I use to do this for the guys with the door shut. You know one of those little secrets to piss them off
By the way any fire is a back fire. I never heard that other one. I go with miss fire, but the other sounds like politically correct bull.
That should fire some one up
01-03-2005 09:13 PM
underdog305 Just so you guy's know the correct terminology is Afterfire if it's out the exhaust, Backfire if it's coming out of the carb. If it's coming out the exhaust, I think it could be an exhaust valve or it's way to rich with poor timing. Consider this: the valve would have to be at least slightly open to ignite the air/fuel and blow out the tail. The timing could be way too retarded (firing way too late). Easy fix!
01-03-2005 08:07 PM
redneckrodder the backfire is out of the exhaust
01-02-2005 10:01 PM
troy-curt I doupt that it would start and run if it was one tooth off. Sounds like the timeing needs adj.

Troy
01-02-2005 09:53 PM
Old School Nut when you say backfire, do you mean out the carb or the exhaust????
01-02-2005 09:05 PM
Max Keith
backfiring

Did you use a timing light when you set your ignition?
Use a timing light to see what your initial advance and total advance are. if your engine barely turns over when you try to start it, that is very indicitive of having the initial advance set too far forward.

Try resetting your distributor at about 10 degrees of initial advance and see if you still have that problem. If you do, as far as the backfiring, it sounds like carburetor or possibly valve set too tight.

A quick way to check it out is to just loosen the distributor a bit and slowly retard it while it runs. If you are way too far in advance, you will notice a slight pickup in rpm, as you retard it.
But, to properly set it, you need a timing light.
01-02-2005 08:45 PM
redneckrodder
distributor timing problem? help

i just finished building a 350 engine. The motor sounds great, but when i go down the road it back fires under acceleration(i beleive). I think the distributor might be off a tooth, because when i start the truck it sounds like it's having a hard time starting because it is out of time. I really hope it is not a problem with the valves because the motor has not even been driven more that 2 miles, and sounds great while idiling and even when i goose it a little at stand still, but backfires when driving, and the valves were adjusted the old fashioned way...while the truck was runngin. Any fast help or info would be very much appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.