Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> broken bolt help
User Name
Password
lost password?   |   register now

Thread: broken bolt help Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-24-2005 02:39 PM
tazzman68 thanks for the input guys, I have made the command decision to r&r the top end, that way if those broken blots give me to much greif, I'll just take the heads into the machine shop to have them bored out.
01-24-2005 12:50 PM
onebadmerc I have a 67 F250 that I swapped the old 352 out for a 390. When I was doing this swap I needed to pull the car manifolds off the 390 and put on the 352 truck manifolds. The first thing I done was I ran the 390 until it was good and hot and then sprayed the exhaust manifold bolts with WD40. Well this partly worked, I still broke 4 of the exhaust manifold bolts. What I did, is I used a pair of vise grips on the broken ends of the exhaust bolt. It worked on gettting 3 of them out but the fourth one I had to drill a hole all the way through the bolt. I started with a small bit then kept stepping up in bit sizes until I was just a little bit smaller than the thread size. I then used a easy out and it came right out. I had the motor out of the truck when I did this, you might be able to drill it with the motor in the truck. If not you might have to pull the head to get the broken bolts out. I have not seen a FE yet that doesn't break exhaust manifold bolts when trying to get them out.
01-24-2005 12:11 PM
stuartc just take the head of it will be easier to get at and you can see what you are doing if the bolt has broken off flush to the head
cheers stuart
01-24-2005 11:35 AM
tazzman68
broken bolt help

Hey all,
Long time no post ( for me anyways )
I just picked up a 1967 Ford Ranger, and the 352 has really bad exhaust leaks. went to swap out manifold gaskets, and found 4 manifold blot broken off in the heads. My question is, should I pull the motor to get at the bolts, or should I just yank the topend?
the only difference I can see between the 2 processes is, the top end is gonna cost me a gasket set, but I can sheck out the internals too, which I see as an advantage. Heres a pic of the truck, and I will get some more up in the photo gallery as soon as possible.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:53 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.