Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> rotating assy. balancing + mixing parts
User Name
lost password?   |   register now

Thread: rotating assy. balancing + mixing parts Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-03-2005 12:48 PM
Docs91RS Most aftermarket pistons and connecting rods come in match wieght sets, but thats not the issue here. Your changing from the stock hyperutectic cast pistions and powdered metal 5.7 rods to a forged piston and a 6 inch forged afetr market rod. The issue isn't that they match eachother its the counter balancing on the crank that needs to be addressed. Anytime you make a change in rotating mass you need to have the crank balanced for the new parts. Wieght has to be added or removed accordingly from the cranks counterwieghts in order to maintain a balanced assembly. For the extra $150-200 it cost for balancing its the smart thing to do.

03-29-2005 07:17 PM
Rob (chuck) Berry
Balancing the old way

Tazz is right; quite often you can get within 10 grams by selecting a heavy rod with a light piston and vice versa then find scale and grind away; although I'd tend to remove material only from the boss on the conrod, when I did fuel quality control for the Aussie airforce I used Sartorious scales accurate to 1/100 of a mg perhaps a local airport can help out, worth a try.
Dynamic balance for race conditions on your rotating mass is a speciality that most shops will not be equipped to handle so may I suggest you put up a new post asking if there is a reliable race engine machinist within coo ee (Aussie term for local-ish) of you the mail service should be able to deliver such a parcel. BTW your engine is basically an air pump so you may need more cam. fuel. different manifolding etc, piston dwell is a good place to start though.

Cheers from Aus

03-25-2005 11:49 AM
old school balancing job....

First and formost a VERY GOOD scale...weight all 8 pistons...grind material off the skirt on each piston heaver than the lighest one to match the lightest piston's weight then do the same thing to the rods..weigh all 8 rods and find the lightest then grind off material on the 7 heaver rods. Taking a small amount off the skirt and off the rod's will balance the parts to each that what your talking about?? Its a lot easier to do with motorcycles.....I have done it on my drag works! Then you should balance the rotating assembly...only a engine shop can do that for you.


Rat Rods Rule!
03-24-2005 11:40 AM
strikingthematch Im willing to bet that forged pistons and 6 inch rods are going to throw your balance job way out. Either find a place to do it there has to be something around there it may be a drive but something. OR if that is out of the question then maybe having new crank that is balanced for your Assembly is the best bet. There are different places that you can buy rotating form that will internally balance the entire rotating assembly for you and then ship it to your door ready to go. Spending extra is better then having your engine shake its self to death. Sure the engine may stay together unbalanced but for how long? Spending all that time and money in an engine and not balancing it is just a waste. IMO

03-24-2005 01:52 AM
rotating assy. balancing + mixing parts

hello all

I have a 95 LT1 and I want to add 6" rods with forged pistons on the stock crankshaft ( the engine won't exceed 6500 rpm )

but unfortunately I live in a place where we don't have any machine shop that have balancing facility

what can I do to minimize the vibrations or harmonics in this setup ?
what is your suggestion ?


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:50 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.