Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Homemade oilpan?
User Name
Password
lost password?   |   register now

Thread: Homemade oilpan? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-27-2005 06:35 PM
docvette
Oil Pan

Quote:
Originally Posted by alex_0227
I'm a little tight for money here, so is it possible to take some sheet metal and make an oil pan instead of buying one?

Alex
Doc here

HAPPY EASTER TO YOU AND YOURS!

Everything is Possible...The only limiting factors are Physics, Funding, Ability, available tools & raw material, and motivation...

I have always found, If I can lay it out in flow chart style, in my mind (Thought Process) , It is like a template I can transfer to the real world...

6 of the products I now manufacture started out as a "Thought" that progressed to (still in the thought stage) "How would I do it?" and "What would it take to make it feasible Do", "What what I need"?...all the way to a go no go mental "Flow~Chart" process before I ever even put pen to paper...and you may think about it for months before you proceed....

Case in point, To fill a need for a no longer made Tach buffer...(I needed one real bad for an old Vette)

I did a little research, found it consisted of 4 discrete electronic components, Inside a housing that looks like a noise suppressor on a coil...

looking in my Electronic "Junk-box" found the 2 resistors and 2 capacitor's (actually 500 of each..I buy in bulk) required to comprise the series parallel Circuit...

Next, (and, still within the thought process) figured out that the metal tube GM used was nothing more than 1/2 EMT conduit...got some of that..($1.10 per 10 feet..) cut it into 3 inch segments, dipped those in Comp orange paint.
Soldered up the components with 3 leads , 2 ~18 ga White, 1~ 18 Ga black.(HEI Tach lead, Tach, and ground)

MADE two wooden blocks using a 1/2 reamer (To get a "Conical" Shape on each end) and Drilled with 2 on one end one on the other, 1/8 hole out each side(to get the wires through..) inserted and centered the electronic components in the conduit and filled that with epoxy...

Got some GENERAL MYSTERY single terminal plugs (To mate with the Stock harness) and Wala! A Tach buffer is born....

I did all this on my living room table (much to the dismay of those around me)

My point here, Is If you can conceive the idea in your mind and make it work in thought...and are of at least Average Ability, You can produce ANYTHING...within the laws of Physics, Cash in your pocket, tools you have, or can borrow or rent, and Just how badly do you want / Need it...

What is it they said about NECESSITY..was somebody's mother...? Find a need and fill it!

Never Discard a good idea, Especially if there is a NEED for it...If you have to, "Shelve" it for a later date, (which gives you more thought/planning room)but follow it out...and If you fail...nobody HAS to know but you...

This is Where Rodding got it's start! SOMEBODY had to think all this stuff up...and bring it into the real world....

Doc
03-27-2005 05:36 PM
mikev You could check out swap meets also, you could get lucky. Especially if you just want a paintable stock pan.
03-27-2005 05:12 PM
woodz428 Larry's correct, if you start with a factory pan rail it isn't a big deal to craft a pan. I've modified several, reversed the sump and made T-pans....whatever is needed for the application. I think a lot of aftermarket custom pans start with a factory rail for the same reason as Larry said.
03-27-2005 05:11 PM
BOBCRMAN@aol.com Make sure you bolt your pan to a block while welding it up. Nothing worse than a finished product that won't bolt down.
03-27-2005 04:38 PM
crazy larry HOW DO YOU THINK the custom oil pan guys make 'em?

only problems i can think of, is starting with a less than desirable gasket flange might cause it to be leak prone. If you had a crapped out pan with a decent flange, you have a great starting point. CStraub i believe, is in the custom pan business, he'd be the cat to ask.
but yes, you can.
03-27-2005 04:02 PM
alex_0227
Homemade oilpan?

I'm a little tight for money here, so is it possible to take some sheet metal and make an oil pan instead of buying one?

Alex

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.