Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> shop air flow
User Name
Password
lost password?   |   register now

Thread: shop air flow Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-06-2005 07:41 PM
Gearhead forever Old furnace fans move alot of air and run very quietly....I've salvaged several from junkers as they slide out as a whole unit. I don't care for those wall exhaust fans as they are usually very noisy.
04-06-2005 06:51 PM
Rob Keller cross ventilation do you only have one door?
you could put those roof turbines to keep the heat from building up in the rafters the exhaust fan are good too when there is no breeze a couple of big fans on the floor like pedestal fans the best fan i ever used was a OLD huge squirrel fan probably 3'x3.5'x4' it would move more air than 4 fans it would dry out a sweaty t shirt in 2 minuets while wearing it

sr66
03-31-2005 08:48 PM
olsixrod
shop air flow

My new shop is 35'x 60'X 13' wall height, the walls are block, and the roof is steel over 5/8 ths sheathing. insulated,with a radiant barrier, without a ridge vent. I have planned for a 4'X4' opening, centered in each eave end, 14' from the floor, for a louvered exhuast fan.
My question is,what is the most effective way to ventalate the shop? My first thought was to mount 2- 48" fans in the openings, and control them with a ridge mounted thermostat.This will give me a complete air change about 6 times an hour, this seemes like a lot of flow and a huge power drain. I'm looking for a gearhead HVAC pro to help me do this right the first time...
I will be welding , fabricating and assembling, in the shop, but no painting (other than rattle cans) and all my machine tools will be under air, in a clean room. my main concern is to keep the "feels like" temp in the shop around 80 deg. with lots of fresh air, not easy to do in south florida. (average daytime air temp is 84 to 86 deg. with 80 % huMUDity) But not create any draughts or fast moving air currents that would interfere with my TIG and MIG welding on the frame jig and building table. any ideas????? thanks,Paul

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:59 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.