Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Loose King Pin
User Name
Password
lost password?   |   register now

Thread: Loose King Pin Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-25-2005 08:51 PM
billg_69gmc
king pin info

Luckily I am swapping out from 6lug to 5 lug and the king pin issue is sorta fresh in my mind.

The two "cups" on top and bottom are king pin bushings. These are supposed to be pressed in. If one has fallen out that is bad, maybe a symptom of another problem. As mentioned by another poster, the retaining bolt secures the king pin in place. Without that you could have a failure since the king pin can come out.

Safest bet is to dissassemble that steering knuckle and replace the crush bearing, bushings and lock pin. A bit of locktite on the end of the threads of the lock pin bolt will keep it from vibrating loose.

The same lock pin design is used on the front of the rear spring shackles of my 59 chevy.

Be mindful that your bushings have to line up with the grease fittings if they are of that nature. Usually you have to puncture the bushings and pry them out. Having them loose is not good. I would definitely check to see if any damage happened to the joint that the king pin is part of... hopefully you got lucky and caught it early.
05-08-2005 02:22 AM
OneMoreTime
Kingpin lock pin

Since I am a ford guy not sure on the chev spindles..on the fords the little top and bottom caps just hold a grease fitting and don't do squat about holding the kingpin in place..

There is a kingpin retaining pin that goes in the center of the axle which lines up with a slot milled in the kingpin..sounds like yours is missing..

Thsi is a special tapered "bolt" that is held in with a nut..look at the other side to see if this is true on yours..

One thing to check is to remove the spindle and see if the axle end is egged..check that before reinstallation..

Sorry about the oops but good you caught it..

OMT
05-08-2005 12:33 AM
hoodoo
Quote:
Originally Posted by Doc68
'28 Rod with 4 inch drop tube axle; 49-54 GM spindles.
Help. I need a quick lesson in king pins and what keeps them in place because the passenger side wants to leave the spindle!
According to the photo located at this link, 1942-47 Chevy front axle , there should be what they call a "Kingpin Lock Pin" (#13 in the photo) which secures the kingpin. Even though the photo is for earlier year Chevies, it should be about the same for your tube axle. That's the same method used on my former '37 Plymouth so I believe it is a common design.
05-07-2005 07:02 PM
Doc68
Loose King Pin

'28 Rod with 4 inch drop tube axle; 49-54 GM spindles.

Was about to drive the rod today when I noticed the passenger side king pin sticking up over an inch above the spindle. Yikes!! How did that happen?!

Inspected both king pins. I have had very little experience with kings pins so I'm not sure what is missing here. They both have thin metal caps on top of the spindle covering the king pins. These are easily removed. On the driver's side bottom, there appears to be some kind of metal cover inside the spindle holding the king pin in place. The passenger side spindle is missing this.

I can tap the passenger side king pin up or down, but can't figure out what kind of snap ring or other device fits top or bottom that prevents the king pin from moving. Obviously the passenger side is missing something as it does not have that fitted metal cap on the bottom of the spindle. When I tried to tap the driver's side spindle up, won't move because of the fitted cap.

Help. I need a quick lesson in king pins and what keeps them in place because the passenger side wants to leave the spindle!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.