Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Help Building A Chevy 383.
User Name
lost password?   |   register now

Thread: Help Building A Chevy 383. Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-27-2005 09:37 AM
Need Help Building a Chevy 383.

Thanx Doc for the information. I really want a radical street rod and yes this truck will be used 90% of the time on the street.
05-27-2005 08:52 AM
Docs91RS Well first of all street/strip is a relative term. It depends on your definition of what constitutes a street engine. Its really just a matter of how radical a combination your willing to endure on the street and how often it will be street driven. Some people build pretty radical engines for the street that idle rough at 1200 rpm and some prefer a smoother idle at the expense of power. I think you need to be abit more specific as to whether this truck is going to be more street or more strip. Also what horsepower numbers are you looking for. With your truck being a 1957 vintage emissions dont apply so it leaves the possibilities wide open.

05-26-2005 06:44 PM
Need Help Building A Chevy 383

The 383 is for a 1957 Chevy Truck 1300 Gentlemen. As for the transmission I do have a TCI Super Street Fighter 400. The rear is a Dana 44 that I plan to convert to posi traction.
05-26-2005 06:28 PM
strikingthematch Try searching the site there is about 100 post of a 383 by now. Go HERE for lots of set ups. There are some set up on there with dart heads.

First thing is what car is this going into?
Rear end? Gear ratio?

Those type of things help find what direction to go in. Your set up will be based on the car and its purpose. Yours being street/strip your going to have a decent cam. heads in the 180-195 cc range to feed the 383. All this will make great power and em...

As for passing the em. test thats pretty simple... For the test put on cats... then when your done with the test swap in the straight pipe. It works like a charm.

05-26-2005 05:55 PM
68NovaSS Your pistons will be the determining factor for your final cr, combined with your chamber cc's. You need to know what your emissions standard is in TX, up here it's dependant upon the year of the car which test is required, i.e. no test for '67 and older cars, tail pipe sniff only and full blown testing to the point it has to have the original air cleaner installed or you have to go to the referee station. Fortunately we can get a seasonal waiver and have no test requirements if it's not driven during the winter months for $18.00.

Many of the parts you buy can be CARB certified but there are so many variables that can throw emissions through the roof it could make passing any test impossible if the state requirement is tough.
05-26-2005 04:40 PM
Help Building A Chevy 383.

I need somebody to help me figure out how to build a street/strip 383 that will pass emission standards. I plan on using Dart cast iron heads and I already have an Eagle 4340 forged crankshaft and Eagle forged H beam rods. I was thinking of buying the 215/64 Platinum Iron Eagle Heads. Would these heads create to much compression? Or should I purchase the 215/72 heads? If anybody out there can get me a combination list for a 383 this would be greatly appreciated. This 383 will see street/strip duty.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 04:34 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.