Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Wet sanding technique
User Name
Password
lost password?   |   register now

Thread: Wet sanding technique Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-28-2005 04:04 PM
SVOHIO
buffing

Thanks for the advice, it's going pretty good so far, I'm about halfway done.
Check it out. The pictures don't do it justice, but it's raining here so no sunshine.
05-28-2005 10:15 AM
Bee4Me Block's are a must on panels as just using your hand will wave it baddly. Which you won't notice till your out in the sun unless it's really bad.
Buffing speed is best kept around 1000 to 1500 RPM.
You need "some" heat but getting up above 1700 will have a greater chance of burning.
I just prefer wool pad on the inital cut with 3M Perfect-It II or III depending on how the compound works with the preticular clear.
3M Swirll Remover on a black waffel pad will finish it nicely.
Then some Hand Glaze to top it off.

Just stay away (or VERY LIGHTLY) from the edges and raised transition areas with the buffer,it will cut thru faster than you will ever believe.

Be SURE the buffer pad direction of spin run's OFF the panel NOT TOWARDS it.

Racecar.
05-28-2005 06:16 AM
baddbob Explaining the process is difficult, your best bet would be to find a knowledgeable person in your area to demonstate. Sanding grit will be determined by how large of a defect needs to be removed. For major major texture problems some people start with 600 or 800 grit then step it down to 1200or 1500, 2000, 2500, 3000. If the paint went on good with just some minor peel then you may want to start with 1500 grit. The finer the grit used the less chance of a cut through and the easier it will be to buff. Sand a 2ft square area then squeegee the water off and check, when all the texture is gone move over and do another area, repeat. When you're done sanding one panel buff it with compond and move to the next- the clear buffs easier imediately after sanding (if it is still green). The slower the buffer turns the less chance you will burn the paint. 3M's perfect it 2 and 3 are good compounds, there are many good compounds available. Whenever possible use a backing pad when wetsanding, I use a thin piece of rubber, some prefer balsa wood. Straight sanding strokes, no circles, and change stroke directions when stepping down to a lighter grit- you will then be able to see when the cutting is done and it will sand faster.

Colorsanding and buffing is best explained and demonstrated in person IMO. I bet the video mentioned would be good.
05-28-2005 12:42 AM
willys36@aol.com You need to buy the video "Color Sanding and Buffing", by Paintucation, available @ paintucation.com. Very thorough and informative step by step how-to.
05-27-2005 06:10 PM
SVOHIO
Wet sanding technique

Thanks for all the info on this board, I painted my car last weekend and it turned out quite nice. Now I'm going to wet sand and buff this weekend. What is the proper technique? What direction do I sand? crisscross, straight line, swirl motion. When using compound on a buffing pad what rpm do I use?
Same question for polishing sponge. I was wondering if someone could take the time to steer me in the right direction. Thank you. Tim

pic of my first paint job

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.