Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> HOLLEY 600 4160 CARB QUESTIONS?
User Name
Password
lost password?   |   register now

Thread: HOLLEY 600 4160 CARB QUESTIONS? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-22-2003 02:57 PM
1BAD80 I suggest that you go to Hollys site and read up on your carb. Also the Knowledge Base has a lot of info.If it's spitting gas it could be the float level, blowen power valve, to much gas pump pressure,sticking float, or crud in the needle jet.
<a href="http://www.holley.com/HiOctn/TechServ/TechInfo/FMCTech.html" target="_blank">http://www.holley.com/HiOctn/TechServ/TechInfo/FMCTech.html</a> OR
<a href="http://www.holley.com/HiOctn/TechServ/TechInfo/Instruct.html" target="_blank">http://www.holley.com/HiOctn/TechServ/TechInfo/Instruct.html</a>

[ May 22, 2003: Message edited by: 1BAD80 ]</p>
05-22-2003 02:23 PM
MI2600 I think he's talking about some of the Holleys have a check valve on top of the front fuel bowl. If I remember the valve is actuated by a lever that is in contact with the driver's side linkage. It is slightly open when you're at idle and closes when you go off idle. I don't know exactly what it's supposed to do. I had a carb rebuilt by a local speed shop and they essentially eliminated it and plugged the hole.
05-22-2003 10:25 AM
MuscleTruck Yep. That's a great carb for a mild SB. It'll give you sufficient power and good economy. You'll want to make sure you spend A LOT of time just simply adjusting your idle mixture screws to make it crisp. Also, you'll want to play around until you find the exacty vacuum secondary spring you need. Don't forget having the right squirter is necessary too.

I have one on my truck. It's been a good carb. Mine was new, but make sure you get a good rebuild on yours. Don't let anyone tell you it's not any good for a mild street setup.

I can't answer you last question. I'm familiar with this style of carb having a transfer tube, and ONE inlet. Hmmm....

Ben T.
05-22-2003 10:18 AM
mr_chickenhead
HOLLEY 600 4160 CARB QUESTIONS?

I recently purchased a used HOLLEY 600 CFM MODEL 4160 CARBURETOR. This style of carb is new to me, I have been spolied with DPP over the years. Is this carb any good for a mild SB Chev?
I was also wondering why there were 2 fuel lines outlets and is that some sort of check valve on the top?

When I stuck it on the car, it spit up through the check valve?

http://www.geocities.com/altereddrea.../600holley.jpg

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.