Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Rear Axle Leak Ford 9 inch
User Name
Password
lost password?   |   register now

Thread: Rear Axle Leak Ford 9 inch Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-19-2005 07:30 PM
IanRiordan
9 inch seals.

I gave up on sealed bearings years ago and now run a 9 inch centre with Holden (local Gm) axles, tubes, bearings and brakes. Check out non c-clip Gm, Dana, Amc etc. Early swing axle M/benz have a seal that should go close, You could make a retainer out of Benz & Ford parts and use a homemade gaskrt behind it. but the other bloke is right, check out the housing first. Almost forgot, how clear is your diff breather? they generate a lot of heat so expanding air has to vent somewhere.
08-19-2005 11:25 AM
johnsongrass1 A bent axle will take out the seal in short order. You could try running inner seals to help keep fluid out of the tube.
08-19-2005 10:19 AM
zonk It's a big bearing housing, originally as far as I know had a sealed bearing, interesting thought on taper roller bearing and seal, Don't know if one could be converted that originally had sealed bearing and still have room.
Have been putting black rtv around outer bearing race see if that would help.

Pretty sure having new axles made this winter go from there.
Thanks for the thoughts.
08-19-2005 10:08 AM
johnsongrass1 Have you tried a gasket on the retainer? OR some RTV around the bearing?

Sealed bearings don't have that much fluid in them. If at all.
08-19-2005 06:24 AM
IanRiordan
bad 9 inch

You may be right on both counts. All 9 inch's run hot due to the sharp pinion tooth (pressure) angle. 2 hours towing a ski boat and I could smell gear oil with the windows up. I'm unfamiliar with napa parts here in Aus, but if it's a small bearing with thin oil and a tall tyre for leverage look out. How about a tapered roller, external seal & higher oil level? Works well in local hybrid ford centre, gm axle tube combo's.
08-17-2005 04:14 PM
zonk
Rear Axle Leak Ford 9 inch

I have a nuisance leak around my right rear tire. I'm using a 57 ford 9 inch, seems like it is always leaking small out of oil between axle flange and axle bearing retainer. I have noticed it on both side, my bearings are doubled sealed napa # 88128R I'm using Synergyn Syngear 11 oil which is red. This looks whats leaking is black, so I'm thinking it's the grease coming out of the bearings. I pulled the right side axle out bearing seems ok, at one time I was using inner axle seal still seemed to leak a little,before I put axles back in have used small amount of rtv black around bearing trying to fix it. I'm wondering possible my right axle is bent alittle causing this? Or since I'm not using inner seal the syngear working through bearing seals slowly washing out the grease? I'm considering have new axles made this winter, starting to pull some splines on the original axles any thoughts ? Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:19 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.