Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Sexy rear end
User Name
lost password?   |   register now

Thread: Sexy rear end Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-07-2002 06:51 PM
axle bastard i don't know beans about a jag, but i can tell you dana 44's are all over. front of ford trucks, back of jeeps, i don't know why a gear set for a jag would be different if its a dana,
hope that is some what of a help.
08-06-2002 06:49 AM
Mrfixmaster Wear a good helmet!!!
08-05-2002 12:53 PM
SJFast A lot of the Jag rears are posi....mine isn't. I haven't researched gear ratios much but there are many different ones available. Mine is a 2.88 : 1 and, with my 33" rear tires, at 7000 rpm in drive I'll be going 238 mph....
08-05-2002 09:35 AM
Mrfixmaster Were all or most of these posi? Mine is coming out of an xj6 sedan.

SJfast, are the Dana 44 gears common? would like to run somewhere between 3.70's and 4.00 to 1. <img src="confused.gif" border="0">
07-31-2002 01:07 PM
SJFast Exactly ! One problem with the XKE is the knockoff hubs. My '91 XJS uses Chevy wheels. It's going into a street-legal 60's sprint car and I've narrowed it from 61 1/2" over the wheel flanges to 50". It measures 25" from each wheel flange to the pinion centerline.

I paid $250.00 for it on eBay.

[ July 31, 2002: Message edited by: SJFast ]</p>
07-31-2002 10:41 AM
hotrodit About 20-25 years ago everybody was using them things over here, not much too worry about that hasn't already been covered, the narrow one was the XKE or E-Type as known over here & the widest one was the mk10, as for wear i've seen every kind on them but if you keep em greased up they are pretty good & theres no excuse they got plenty of grease nipples.
Obviously the hard one to get is the XKE but the XJ6 & XJS are common & cheap to buy over here.
good luck
07-30-2002 12:26 PM
hot_rod_kid go to to get info on everything ya need ta know. <img src="graemlins/pimp.gif" border="0" alt="[pimp]" />
07-28-2002 02:21 PM
SJFast A T-bucket, with about a third of the sprung weight of a Jag sedan, shouldn't be bothered by any tire size. Perhaps whoever told you this was referring to wheel offset, i.e. moving the wheel centerline further away from the upright bearing's centerline. That would create a lever effect on the hub bearings. With your light weight deal there should be no problem. I ran into my import car expert in the hardware store yesterday and he advised me to replace the bearings, etc. just inboard of the brake rotors. They are the "weak link", if there is such a thing, in the Jag rear. This is because the half-shafts also act as the upper arm in the suspension design and take a side load as well as supporting the U-joints in rotation.
07-28-2002 07:27 AM
Mrfixmaster The warning I had was that they don't hold up well with really wide tires, I'm only running 12"wides, so don't know if that applies to me or not. Thanks for all your input and advice. I'll keep you posted of the progress.
07-26-2002 09:01 AM
SJFast I haven't run it yet. I sure don't see why wheel bearings would be a problem though. Especially in a lightweight T-bucket. If they stand up in a big, heavy Jaguar sedan, why would they be a concern in your application ? Check with a Jaguar dealer maybe ?
07-26-2002 07:41 AM
Mrfixmaster Thanks for the advice. I have bought the rear end, but it has not been delivered yet. Thought about putin it in my T-Bucket, but also thought about just starting another one!! (Haven't broached that subject with the war department yet) was really wondering about longevity. I've heard tales about the wheel bearings being the weak link of these. Any troubles there?? <img src="confused.gif" border="0">
07-26-2002 04:12 AM
SJFast Hang in there. One thing to remember is the lower arms must be level through the pivot points. This makes the pinion also level. Your engine should therefore be level in the chassis if you want good life from your U-joints.
07-26-2002 03:39 AM
Mrfixmaster Haven't gotten far enough along to know exactly what to ask about, just wondered what problems/engineering "challenges" others had run into before I start.
<img src="confused.gif" border="0">
07-25-2002 12:19 PM
SJFast Mrfixmaster...I'm finishing one up right now. I really like the engineering on the thing. It's all U.S. threads and fasteners (no metric), it's a Dana 44 center section, and I found it to be a pleasure to work on. One thing you might want to be aware of is the pinion is offset about 1" to the right. Your driveshaft length might be an issue. Anything specific you want to know ?

07-25-2002 11:16 AM
helrazr3 you got my attention alright nice move, but i know nothing about jag rearends, except that thier complicated and expensive good luck though
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:58 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.