Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> How much rear end grease?
User Name
lost password?   |   register now

Thread: How much rear end grease? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-09-2002 01:48 PM
axle bastard clunking is NOT good. worn bearings can cause excessive backlask that can clunk. excessive backlash can also cause misalignment of the gears causing a whine.
what kinda rear you got in the grem?
if the play is in the pinion yoke/ pinion, that will cause misalignment, giving the clunk and whine.

[ August 09, 2002: Message edited by: axle bastard ]</p>
08-09-2002 09:28 AM Your rear end has a pipe plug in it about half way up (all I have seen are on the back sheet metal part of the housing but there might be some with it in the cast iron gear carrier I guess). Regardless, fill the unit thru this hole 'til full to the bottom thread in the hole and it will be properly filled.

I don't understand where the slop is in your yoke. If it is in the pinion shaft, a very little slop is proper and reflects the pre-set clearance in the gears. If this is the case, the only way to check if it is too much is to expose the gears and measure the lash per motor manual instructions. If the slop is in the U-joint, REPLACE IT! There should be NO slop in it. Regardless, I would go thru the trouble of checking the gears (messy and a hassle but worth the effort). If it is a used unit, as long as you have it apart, check the bearings for burn, pitting, or wear also.

Bearings whine all the time while bad gears whine on power up or breaking.

[ August 09, 2002: Message edited by: ]</p>
08-09-2002 07:37 AM
How much rear end grease?

Hey all.
I just cruised my Gremlin down the road about 1/4 mile and back and noticed 2 things.
1. There is a whinning noise in the rear end. I was told by one person that 2 quarts of rear grease is needed to fill it up and then by another that it takes 3 to 3.5 to fill it up. Is the whinning sound due to lack of grease?
2. I have play in the yoke. The part where the driveshaft hooks to the rear end. When I put it in gear it goes thump and moves. Should I be concerned?
Thanx, HG

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 08:14 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.