Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Tip of the day #19
User Name
Password
lost password?   |   register now

Thread: Tip of the day #19 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-09-2005 04:08 AM
adtkart I hope you put on several coats using the air brush. They are not meant for heavy coverage, so it may be real thin where you sprayed.
10-08-2005 11:10 PM
skeeveman We use the "pyrex" measuring cups, or whatever they're called. You can get them from wally world, they're for cooking, and come in may sizes, from shotglass lookiing cups and on up. Nice thing about them is, they're marked very legibly, super easy to clean up, and can take a beat'n....been dropped on the concrete floor multiple times with no problem.....but once in a while they hit the floor just right and they will break.
10-08-2005 09:16 PM
FrankR
Quote:
Originally Posted by milo
Interesting... I can't understand risking having WD40 anywhere near a paint project let alone mixing primer or paint in a wd40 cap... I've seen to many disaster cases from Wd40..crazy risk..

What I'found is those little medicine cups they have in the hall in hospitals won't be affected by solvents and have measure marks engraved into them.

I belive in small batches but won't let WD40 or it's cap anywhere near a paint project..
Fisheyes are for fish
I agree that it would have been risk had I not throughly cleaned the cap in hot soapy water and washed it in wax & grease remover before hand. I probably should have mentioned this and not assume everyone would know it must be clean. It just happened to be what I had available. I don't use the WD anywhere near where I paint. I don't have a paint booth though. I did this in my open driveway.

But I like the medicine cups idea MUCH better.
10-08-2005 09:04 PM
milo Interesting... I can't understand risking having WD40 anywhere near a paint project let alone mixing primer or paint in a wd40 cap... I've seen to many disaster cases from Wd40..crazy risk..

What I'found is those little medicine cups they have in the hall in hospitals won't be affected by solvents and have measure marks engraved into them.

I belive in small batches but won't let WD40 or it's cap anywhere near a paint project..
Fisheyes are for fish
10-08-2005 08:50 PM
FrankR
Tip of the day #19

Disclaimer: I don't have the means to strip and paint my car at one time so I must do my work a panel at a time the reason I chose to do it this way.

So I tried my hand with an air brush today. I used it to shoot all of my stripped panel edges and weld seems on my car with epoxy sealer since it was bare metal. I am just doing the passenger side. Quarter panel, door, fender. I wasn't quite ready to shoot the rest of the panels and I hated to mix up such a small amount for my HVLP gun. I just wanted to protect these areas from rust before I can do the rest.

I used the little red cap off the top of a WD40 can to mix my epoxy. I dipped it into my epoxy twice and poured it into a mixing cup, then added one cap full of hardener. 2:1. Since I didn't have to tip my paint can to pour, it made minimal mess.

With this small amount, I was able to cover the entire weld seem around my wheel arch, all door edges, fender edges, door jamb edges, and some other areas.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.