Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Help with Lowering
User Name
Password
lost password?   |   register now

Thread: Help with Lowering Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-15-2005 09:10 PM
xntrik
Quote:
Originally Posted by hot-rod-ford
Thanks Xntrik.
I really just want the car dropped a little in the front. Being able to lower it up and down at will does not really concern me, as long as it rides good after I lower it and don't have any real problems w/ it bottoming out.

From what you mentioned, it seems like dropped spindles would work the best for me. I am definitely concerned about keeping the correct geomety and a good ride. I just wanna clost the gap between the fender well and the top of the tire.

The way the rear sits as of now is fine w/ me. I had the leaf springs reconditioned a while back. It rides and sits good as it is.

My budget isn't huge. I'm hoping I could do it for possibly under $500.

Thanks again for the help. If you or anyone else have anything to add I'd appreciate it.

Thanks!
Dropped spindles are not inexpensive.

You can reasonably lower the car by cutting the front coils 1/2 or 1 full coil off the bottom end.

The center of the lower control arm pivot (bolt) to the center of the ball joint pivot should be level. If the car is no lower than that, it should drive ok and not be too bad bottoming out with cut springs.

Park it on level concrete and have a couple of fat buddies sit on the core support to lower the front. Look at the tires and the control arm. Is that good enough height? You decide.

I'd try that first. You are going to end up buying new front springs anyway, so might as well try to cut them.

www.readershotrods.com drag cars/georges
10-15-2005 09:54 AM
hot-rod-ford Thanks Xntrik.
I really just want the car dropped a little in the front. Being able to lower it up and down at will does not really concern me, as long as it rides good after I lower it and don't have any real problems w/ it bottoming out.

From what you mentioned, it seems like dropped spindles would work the best for me. I am definitely concerned about keeping the correct geomety and a good ride. I just wanna clost the gap between the fender well and the top of the tire.

The way the rear sits as of now is fine w/ me. I had the leaf springs reconditioned a while back. It rides and sits good as it is.

My budget isn't huge. I'm hoping I could do it for possibly under $500.

Thanks again for the help. If you or anyone else have anything to add I'd appreciate it.

Thanks!
10-12-2005 07:05 PM
xntrik First you have to decide what your goal is.
Do you just want it low, or to go up and down at will?
Are you willing to change the front and rear suspensions?
Do you have an unlimited budget?

How low do you want it? It is probably 2 " lower than new already.

Lowering stock suspension is limited by 2 things. Drive and ride.
The lower control arm pivot and the lower ball joint pivot should be horizontally level. If you go lower than that on a stock suspension, it will not drive well.
Achieving this lowering is best done with new lowering springs, rather than cutting coil springs, which will help prevent bottoming out on bumps.

Dropped spindles are a better idea. Check with FatMan's about availability.

Rear leaf springs are best done with reverse eyes and minimal use of lowering blocks.

At the top of this thread page, click on knowledge base, then type in suspension lowering and click search.
10-12-2005 03:55 AM
hot-rod-ford
Help with Lowering

Hello,
I am new here and a novice hotrodder. I have a '63 Thunderbird that I would like to lower a few inches but an unsure about the best/proper way to do so.

I have read things about cutting coils, getting dropped spindles and installing air bags, but I'm really unsure of which is the best way to go. I have never done this so, skill is definitely a factor. I have no problem learning how to do things and I'm pretty handy w/ tools.

Anyway, if anyone could possibly tell me how they've lowered their cars or point me to some tech articles that I could read, I'd greatly appreciate it.

Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.