Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Axle Seal replacement
User Name
lost password?   |   register now

Thread: Axle Seal replacement Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-13-2005 09:21 PM
Rear Seal Axle Replacement

Thanks for the replys....Just what the Doctor ordered!!!! Jim, the photo's you provided look exactly like what I have. I will take your advice on doing the bearings also. Again THANKS for the reply's....Randy
12-12-2005 09:45 PM
jimfulco Remove the brake drums if they're not off already. Put the rear end up on 3 jack stands so it's in the same position it was in the car, nose forward, etc. Put a drain pan under the center & remove the cover. Sometimes the bottom bolt hole will connect to the inside, and the oil will come out the hole. If not, loosen all the bolts 2 or 3 turns, then pry the bottom of the cover outwards to let the oil out.

Turn the differential carrier until you can see one end of the pinion shaft and the small bolt head a little to the right of the shaft. That bolt retains the shaft. Remove the bolt, then slide the shaft out toward you. You may have to stick your finger around to the other side & give it a shove. This picture shows the retaining bolt partially unscrewed.

Once the shaft is out, don't turn the driveshaft yoke or axles any more than you have to, because if you do, the pinion gears (spider gears) might move out of place & that can be a PITA to get back right. You'll need to turn the carrier back a bit to get access to the inner axle ends, but only a little bit.

Push one axle inwards about 1/4" to expose the C-clip on its inner end. This can only be done after the pinion shaft is out. Slide out the C-clip (a magnet-on-a-stick tool is good for this), and then do the other axle. Slide the axles out.

Inspect the axles where the outer axle bearings ride. If there's a groove about a half-inch wide, the axle should be replaced, along with the bearing. If you can see a pattern but there's no groove, you're OK. MIght consider replacing the bearings anyway while you're this far in, but it's up to you.

Remove the axle seals. There's a tool for this, but a good-quality claw hammer usually works for me. There's also a tool to install the seals, but the same hammer & a chunk of 2x4 work fine if you're careful not to distort the seal. Install the seals (with a touch of oil on the lips), axles, C-clips (push the axles outward so they don't fall off), pinion shaft, retainer bolt, & cover. If the rear's out, you can drop the nose down and pour the oil in before installing the cover.

12-12-2005 09:16 PM
Bumpstick See if this helps...?
12-12-2005 06:54 PM
Axle Seal replacement

I would like to replace the rear end axle seals, the rear is a 8.5 inch/3.42 posi unit from a 78 camaro. Is there an article/book/web site that shows alot of pictures/ explanation of how to do this. I have searched this site and purchased the 78 Camaro Haynes book but I am a BEGINNER when it come to rear-ends. Currently the rear end is out of the vehicle with easy access. Thanks....Randy

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 11:59 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.